manualshive.com logo in svg

Chevrolet T-Series, Owner'S Manual

Share
Download
Chevrolet T-Series Owner'S Manual Download Page 70

To charge a trailer’s air brake system do the
following:

1. Move your vehicle into the proper position.

2. Apply the parking brake by pulling the yellow

parking brake knob out.

3. Hook up the trailer air system properly.

4. Get into the vehicle.

5. Push and hold down the regular brake pedal.

6. Push in both the yellow parking brake and

the red trailer air supply knobs. This will
charge your trailer’s air system.

After a few minutes, the trailer system should be
fully charged. When it is, the air pressure gage will
show about 125 to 135 psi (862 to 931 kPa).
See

Air Pressure Gage on page 118

for more

information.

For driving with a trailer, the yellow and red, if
equipped, knobs must be pushed in. When you are
not pulling a trailer, the red trailer air supply
knob must be pulled out.

{

CAUTION:

If you apply any one of the air brake
parking controls while the vehicle is
moving, your rig will stop suddenly. If you
are not ready for this, you or others could
be injured. Do not apply any one of these
controls while you are driving, unless you
have to make an emergency stop.

70

Summary of Contents for T-Series







































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands