Chevrolet T-Series Owner'S Manual Download Page 213

Page: 213 / 326

Item Number

Item

Remarks

Steering Drag Link Ends

One fitting each end.

Steering Column U-Joints

One fitting each joint.

Pivot Points and Hinges

Apply chassis lubricant.

Slack Adjuster***

One fitting.

Brake Cam Roller Pins***

Apply engine oil.

Front Steering Knuckles

One fitting each side, lower bushing. (Hand-operated

grease gun only.) Hand-pack upper bearing.

Front Wheel Bearings*

Hand-pack or lubricate.

Steering Tie Rod Ends

One fitting each end.

Spring Slip Pads** (Multi-leaf Only)

Apply chassis lubricant.

Clutch Release Bearing**

Cup or fitting.

Battery Terminal (except “ST” type)

Keep coated with petroleum jelly.

Parking Brake Bell Crank**, $

One fitting.

Transmission*

Fill to level of filler plug.

Transmission-Automatic*,**,†

Check fluid level.

Propshaft Slip Joints

One fitting each joint; lubricate with

GM Part No. 1051344 Wheel Bearing Lubricant.

Propshaft U-joints

One fitting each joint (1480 and 1550 Series);

lubricate with GM Part No. 1051344 Wheel Bearing

Lubricant. Two fittings each joint (1610 Series and

larger); lubricate with GM Part No. 1051344 Wheel

Bearing Lubricant.

Rear Wheel Bearings*

Hand-pack or lubricate.

Rear Axle*

Fill to level of filler plug.

Parking Brake Clevis Pin$

Apply chassis lubricant.

213

Summary of Contents for T-Series







































































































































































































































































































































Search results

Summary of Contents for T-Series

Reviews:

Brands by name

Popular brands

Chevrolet T-Series, Owner'S Manual

Search results

Summary of Contents for T-Series

Reviews:

Brands by name

Popular brands