manualshive.com logo in svg

Chevrolet T-Series, Owner'S Manual

Share
Download
Chevrolet T-Series Owner'S Manual Download Page 183

3. Make sure the fuel lines are securely

connected.

4. Make sure the fuel filter is cool to the touch.

5. Use a clean cloth to remove dirt and oil

from the fuel filter head and breather valve.

6. Use the palm of your hand to repeatedly press

and release the plunger (1) at the top of the
fuel filter priming pump. Continue until
the plunger resistance becomes firm. This
may take from 20 to 100 times, depending
upon fuel tank location.

7. Turn the fuel filter breather valve screw (2) left

(counterclockwise) several turns to open the
breather valve.

8. Use the palm of your hand to repeatedly

press and release the plunger (1) at the
top of the fuel filter priming pump until fuel
begins to seep from the breather valve.

9. Tighten the fuel filter breather screw (2) to the

specified torque, 4.9

Y

(43 in. lbs).

10. Use the palm of your hand to press and

release the plunger (1) at the top of the
fuel filter priming pump about 20 more times.
This sends fuel to the engine.

11. Use a clean cloth to remove any fuel from the

fuel filter and surrounding area.

12. Start the engine and allow it to idle for a

few minutes.

13. Check the fuel filter for leakage.

183

Summary of Contents for T-Series







































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands