manualshive.com logo in svg

Chevrolet T-Series, Owner'S Manual

Share
Download
Chevrolet T-Series Owner'S Manual Download Page 121

AM-FM Radio

Playing the Radio

ON (Power):

Press this knob to turn the system

on and off.

VOL (Volume):

Turn this knob clockwise or

counterclockwise to increase or to decrease
the volume.

DISP (Display):

Press this knob to switch the

display between the radio station frequency,
the time, and the alarm status.

Finding a Station

BND (Band):

Press this button to switch between

FM or AM. The display shows the selection.

z y

(Tune):

Press the up arrow to go to the

next radio frequency. Press the down arrow to go
to the previous radio frequency.

To seek stations, press and hold either arrow for a
second or longer. The radio seeks to the next or
previous station.

The radio only seeks stations with a strong signal
that are in the selected band.

t

(Scan):

Press this button to scan radio

stations. The radio goes to a station, plays for a
few seconds, then goes to the next station.
Press this button again to stop scanning.

The radio only scans stations with a strong signal
that are in the selected band.

121

Summary of Contents for T-Series







































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands