manualshive.com logo in svg

Chevrolet Silverado 2020, Owner'S Manual

Share
Download
Chevrolet Silverado 2020 Owner'S Manual Download Page 356

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-

13337620) - 2020 - CTC - 1/27/20

Vehicle Care

355

See

California Proposition

65 Warning

0

325

and the back

cover.

Vehicle Storage

{

Warning

Batteries have acid that can burn
you and gas that can explode.
You can be badly hurt if you are
not careful. See

Jump Starting -

North America

0

415

for tips on

working around a battery without
getting hurt.

Infrequent Usage: Remove the
black, negative (

−

) cable from the

battery to keep the battery from
running down.

Extended Storage: Remove the
black, negative (

−

) cable from the

battery or use a battery trickle
charger.

Negative Battery Cable
Disconnection

{

Warning

Before disconnecting the negative
battery cable, turn off all features,
turn the ignition off, and remove
the key, if equipped, from the
vehicle. If this is not done, you or
others could be injured, and the
vehicle could be damaged.

Caution

If the battery is disconnected with
the ignition on or the vehicle in
Retained Accessory Power
(RAP), the OnStar back-up
battery will be permanently
discharged and will need to be
replaced.

1. Make sure the lamps, features,

and accessories are turned off.

2. Turn the ignition off and

remove the key, if equipped.

For vehicles equipped with the Stop/
Start system:

1. Loosen and remove the

negative battery cable nut (1)
at the battery sensor
connection.

2. Remove the negative battery

cable (2) from the battery
sensor stud.

3. Cover the negative battery

cable terminal, battery sensor
stud, and negative battery post
with a non-conductive material
to prevent any contact with the
negative battery cable.

Summary of Contents for Silverado 2020
















































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands