manualshive.com logo in svg

Chevrolet Silverado 2020, Owner'S Manual

Share
Download
Chevrolet Silverado 2020 Owner'S Manual Download Page 26

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-

13337620) - 2020 - CTC - 1/27/20

Keys, Doors, and Windows

25

Laws in some communities may
restrict the use of remote starters.
Check local regulations for any
requirements on remote starting of
vehicles.

Do not use remote start if the
vehicle is low on fuel. The vehicle
may run out of fuel.

The vehicle cannot be remote
started if:

.

The RKE transmitter is inside
the vehicle or if the key is in the
ignition.

.

The hood is not closed.

.

There is an emission control
system malfunction and the lamp
is on.

.

The ignition is in any mode other
than off.

.

The hazard warning flashers
are on.

.

Two remote starts or a remote
start with an extension have
been used.

.

The vehicle is not in P (Park).

The engine will turn off during a
remote vehicle start if:

.

The coolant temperature gets
too high.

.

The oil pressure gets low.

The RKE transmitter range may be
reduced while the vehicle is running.

Other conditions can affect the
performance of the transmitter. See

Remote Keyless Entry (RKE)
System

0

13

.

Starting the Engine Using Remote
Start

1. Press and release

Q

.

2. Immediately press and hold

/

until the turn signal lamps flash
or for at least four seconds.

When the vehicle starts, the
parking lamps will turn on. The
doors will be locked and the
climate control system may
come on.

The engine will continue to run
for 15 minutes. After
30 seconds, repeat
Steps 1 and 2 for a 15-minute
time extension.

Turn the ignition on to operate the
vehicle.

Extending Engine Run Time

The engine run time can be
extended by 15 minutes, for a total
of 30 minutes, if during the first
15 minutes Steps 1 and 2 are
repeated while the engine is still
running. An extension can be
requested 30 seconds after starting.

A maximum of two remote starts,
or a single start with an extension,
is allowed between ignition cycles.

The vehicle's ignition must be
turned on and then back off to use
remote start again.

Canceling a Remote Start

To cancel a remote start, do one of
the following:

.

Press and hold

/

until the

parking lamps turn off.

Summary of Contents for Silverado 2020
















































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands