Home
/
Chevrolet
/
Silverado 2020
/
Owner'S Manual

Chevrolet Silverado 2020, Owner'S Manual

Share

Page: 354 / 495

Chevrolet Silverado 2020 Owner'S Manual Download Page 354

Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-

13337620) - 2020 - CTC - 1/27/20

Vehicle Care

353

How to Disable the Brake Pad
Life System

The brake pad life system can be
turned off. This may be necessary if
aftermarket brake pads without wear
sensors are installed. When the
system is turned off, the front and
rear brake pad life percentages will
not display. However, the built-in
wear indicators that make a
high-pitched warning sound when
the brake pads are worn can still
determine when the pads should be
replaced. See

To turn off the brake pad life system:

1. Display Brake Pad Life on the

DIC. See

Driver Information

Center (DIC) (Base Level)

or

Driver Information Center (DIC)
(Midlevel and Uplevel)

2. Select DISABLE.

To turn the brake pad life system
back on, follow the above steps but
select ENABLE in Step 2.

Brake Fluid

The brake master cylinder reservoir
is filled with GM approved DOT 4
(1500) or DOT 3 (2500/3500) brake
fluid as indicated on the reservoir
cap. See

Engine Compartment

for the location of

the reservoir.

Checking Brake Fluid

With the vehicle in P (Park) on a
level surface, the brake fluid level
should be between the minimum
and maximum marks on the brake
fluid reservoir.

There are only two reasons why the
brake fluid level in the reservoir may
go down:

.

Normal brake lining wear. When
new linings are installed, the
fluid level goes back up.

.

A fluid leak in the brake
hydraulic system. Have the
brake hydraulic system fixed.
With a leak, the brakes will not
work well.

Always clean the brake fluid
reservoir cap and the area around
the cap before removing it.

Do not top off the brake fluid.
Adding fluid does not correct a leak.
If fluid is added when the linings are
worn, there will be too much fluid
when new brake linings are
installed. Add or remove fluid, as
necessary, only when work is done
on the brake hydraulic system.

{

Warning

If too much brake fluid is added, it
can spill on the engine and burn,
if the engine is hot enough. You
or others could be burned, and
the vehicle could be damaged.
Add brake fluid only when work is
done on the brake hydraulic
system.

«
...
352
353
354
355
356
...
»

Summary of Contents for Silverado 2020
















































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands