Champion DH5000T Series Installation And Operation Manual Download

Page: 10 / 116

Installation

Dishwashers are shipped from the factory for straight-through operation. Refer to
page 4 to convert the dishwasher from straight-through to corner operation.

The dishwasher has 4 adjustable feet for leveling.

Level the dishwasher front-to-back and side-to-side.

Straight-through Operation Shown

Placement

(continued)

Dish Table Connections

Level the dishwasher and dish tables to the required height and fit the dish table flanges

over the ends of the dishwasher tank. Refer to the illustration below.

Lift the dishwasher track assembly out of the dishwasher and set aside.

Remove the dishwasher side panels (front and side panel for corner operation).

Apply a NSF approved sealant between the table flanges and the wash tank.

Drill a minimum of two holes through the table flange and the inner wash tank.

Install stainless steel truss head screws or rust-proof rivets to secure the table and tank.

Reinstall the panels and track assembly.

NOTE:

Dish tables should be securely fastened to the dishwasher after the dishwasher is permanently
located and the utilities are connected.

9/32”

Inner Wall of

Wash Tank

Dish Table Flange

Drill holes, apply NSF sealant,

& fasten flange to wash tank

Panel

Control

Panel

Adjustable Feet

Summary of Contents for DH5000T Series





















































































































Search results

Summary of Contents for DH5000T Series

Reviews:

Related manuals for DH5000T Series

Brands by name

Popular brands

Champion DH5000T Series, Installation And Operation Manual

Search results

Summary of Contents for DH5000T Series

Reviews:

Related manuals for DH5000T Series

Brands by name

Popular brands