manualshive.com logo in svg

Champion D-H1M5, Installation/Operation Manual With Service Replacement Parts, Page: 34 / 77

Share
Download
Champion D-H1M5 Installation/Operation Manual With Service Replacement Parts Download Page 34

24

Troubleshooting

Troubleshooting

Before calling for service check the following conditions.
1.  Dishwasher main power and water supply is on.
2.  Machine has been assembled correctly.
3.  Drain is closed.
4.  Screens and pump intake screen are clear.
5.  Doors are closed and secure.

Condition 

Cause 

Solution

Dishwasher will not run.

Machine washes

constantly.

Wash tank water temp

is low when in use.

Door not closed.

Main power OFF

Dishwasher Power OFF.

 

Timer or door switch 

defective

Close door completely.

Check breaker on panel.

Turn dishwasher ON.

Incoming water temp at 

machine too low
Defective thermometer
Defective thermostat
Defective heater 
Defective solenoid valve
Heater element limed up

Increase water 

temperature
Contact Service Agent
Contact Service Agent
Contact Service Agent
Contact Service Agent
Clean element

Defective ckt. bd.
Defective fill valve
Defective drain valve
Defective float switch

Tripped motor overload
Defective motor

Low or no water.

Water fills constantly

Wash motor won’t run

Contact Service Agent

Reset motor overload

Replace motor

Main water supply off.
PRV setting incorrect
Solenoid strainer clogged.
Solenoid valve defective.
Drain valve defective
Stuck or defective float.

Open supply valve.
Adjust the PRV setting
Clean strainer.
Contact Service Agent.
Contact Service Agent.
Clean or replace.

Contact Service Agent

Summary of Contents for D-H1M5














































































Reviews:

No comments