Champion D-H1M5 Installation/Operation Manual With Service Replacement Parts Download Page 18 | Manualshive

Page: 18 / 77

Champion D-H1M5 Installation/Operation Manual With Service Replacement Parts Download Page 18

8

1. All models are GRAVITY DRAIN machines equipped with a 2" O.D. hose connection.

2. The maximum flow rate is 15 U.S. gpm/56.8 Lpm.

3. Drain height for all models must not exceed 8-7/8" [225mm] above the finished floor.

4. The drain connection is made to the dishwasher from underneath the machine. An access

hole is provided in the machine base.

NOTE:

DO NOT VENT THE DISHWASHER INTO WALLS, CEILINGS OR ENCLOSED PLACES.

All venting must comply with local codes.

Ventilation Connections

Installation

Drain Connections

Vent Fan Signal Connection

A two point terminal block is provided inside the top-mounted control cabinet to provide
a 120VAC, 1 AMP Max Load signal.

NOTE:

The Vent Fan Signal Connection supplies 120VAC to a control relay (supplied by others) when the

dishwasher is ON and O VAC when the dishwasher is OFF. Power to operate the vent fan

(supplied by others) must be supplied separately.

VENT FAN 120VAC

10

«
...
16
17
18
19
20
...
»

Summary of Contents for D-H1M5














































































Reviews:

No comments