background image

  

Warranty 

Rev 64022-20100514 E

 

 

25

 

EMISSION CONTROL SYSTEM WARRANTY 

 

The following are specific provisions relative to your Emission Control System Warranty 
Coverage.

 

 
Emission Control System Warranty (ECS Warranty) for 1997 and later model year engines): 
 

1. APPLICABILITY:

 This warranty shall apply to 1997 and later model year engines). The ECS 

Warranty Period shall begin on the date the new engine or equipment is delivered to its original, 
end-use purchaser, and shall continue for 24 consecutive months thereafter. 
 

2. GENERAL EMISSIONS WARRANTY COVERAGE 

CPE warrants to the original, end-use purchaser of the new engine or equipment and to each 
subsequent purchaser that each of its small off-road engines is: 
a. Designed, built and equipped so as to conform at the time of sale with applicable 
regulations under section 213 of the Clean Air Ac, as amended, 42 U.S.C. 7401 et seq. 
b. Free from defects in materials and workmanship that cause the failure of a warranted 
part to be identical in all material respects to the part as described in the engine manufacturer’s 
application for certification for a period of two years. 

 
3. THE WARRANTY ON EMISSION-RELATED PARTS WILL BE INTERPRETED AS 
FOLLOWS:

 

a. Any warranted part that is not scheduled for replacement as required maintenance in 

the Owners Manual shall be warranted for the ECS Warranty Period. If any such part fails during 
the ECS Warranty Period, it shall be repaired or replaced by CPE according to Subsection “d” 
below. Any such part repaired or replaced under the ECS Warranty shall be warranted for any 
remainder of the ECS Warranty Period. 

b. Any warranted, emissions-related part which is scheduled only for regular inspection 

as specified in the Owners Manual shall be warranted for the ECS Warranty Period. A statement 
in such written instructions to the effect of “repair or replace as necessary”, shall not reduce the 
ECS Warranty Period. Any such part repaired or replaced under the ECS Warranty shall be 
warranted for the remainder of the ECS Warranty Period. 

c. Any warranted, emissions-related part which is scheduled for replacement as required 

maintenance in the Owner’s Manual shall be warranted for the period of time prior to the first 
scheduled replacement point for that part. If the part fails prior to the first scheduled replacement, 
the part shall be repaired or replaced by CPE according to Subsection “d” below. Any such 
emissions-related part repaired or replaced under the ECS Warranty, shall be warranted for the 
remainder of the ECS Warranty Period prior to the first scheduled replacement point for such 
emissions-related part. 

d. Repair or replacement of any warranted, emissions-related part under this ECS 

Warranty shall be performed at no charge to the owner at a CPE Authorized Service Outlet. 

e. The owner shall not be charged for diagnostic labor which leads to the determination 

that a part covered by the ECS Warranty is in fact defective, provided that such diagnostic work is 
performed at a CPE Authorized Service Outlet. 

f. CPE shall be liable for damages to other original engine components or approved 

modifications proximately caused by a failure under warranty of an emission-related part covered 
by the ECS Warranty. 

g. Throughout the ECS Warranty Period, CPE shall maintain a supply of warranted 

emission-related parts sufficient to meet the expected demand for such emission-related parts. 

h. Any CPE Authorized and approved emission-related replacement part may be used in 

the performance of any ECS Warranty maintenance or repair and will be provided without charge 
to the owner. Such use shall not reduce CPE’s warranty obligation. 

i. Unapproved add-on or modified parts may not be used to modify or repair a CPE 

engine. Such use voids this ECS Warranty and shall be sufficient grounds for disallowing an ECS 
Warranty claim. CPE shall not be liable hereunder for failures of any warranted parts of a 
CPE engine caused by the use of such an unapproved add-on or modified part. 

Summary of Contents for 64022































Reviews: