background image

© 2009 Wayne Water Systems

330002-001 3/09

Sewage 

Pump

Operating Instructions and Parts Manual 

Models SEL40 and SEL50

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. 
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or 
property damage! Retain instructions for future reference.

Description

A sewage system consists of a pump, 
control switch, and a ba sin for use in 
ap pli ca tions where less than six toilets 
(units) are dis charged into the basin. 
The sys tem is generally con trolled by a 
float switch with a plug-in-plug which 
accepts the pump plug and in turn 
plugs into a 115 volt outlet.
The float switch is a wide angle 
differential switch that rises with the 
liquid level and turns the pump on. 
As the liquid level decreases the float 
lowers and turns the pump off. This 
pump is in tend ed for use in do mes tic 
sewage lift stations. It is suitable for 
pumping sewage, effluent, wastewater, 
groundwater and other non ex plo sive, 
non cor ro sive liquids with up to 2 inch 
solids.

For parts, product & service information

visit 

www.waynepumps.com

REMINDER: Keep your dated proof of purchase for warranty purposes!  

Attach it to this manual or file it for safekeeping.

 Specifications

  Power supply requirements .............. 115V, 60 hz
  Circuit requirements .......................... 15 amps (min)
  Motor duty ......................................... Intermittent
  Motor ................................................. 115V, 1 Phase, 1725 RPM
  Horsepower  ....................................... 4/10 (SEL40); 1/2 (SEL50)
  Motor full load .................................. 12 amps
  Liquid temperature range ................. 40º F to 120º F
  Max. operating position .................... 45º from vertical
  Dimensions ......................................... 13-1/2 inch x 11 inch
  Intake ................................................. 2 inch
  Discharge ............................................ 2 inch NPT female, 3 inch 

NPT male

  Cut-in level (factory set) .................... 18 inch
  Cut-out level (factory set) ................. 10 inch
  Differential ......................................... 8 inch
  Switch ................................................. 90º wide angle  

mechanical tether switch

  Power cord ......................................... 16 gauge 3 conductor  

w/plug

 Construction

  Motor body material ............Cold rolled steel
  Motor housing ......................Glass reinforced  

polypropylene

  Volute ....................................Glass reinforced ABS
  Impeller .................................Glass reinforced PBT
  Seal plate ..............................Cast Iron
  Shaft seal ...............................End faced mechanical

Performance

GALLONS PER hOuR At tOtAL hEAD IN fEEt

Model

10

15

200

SEL40

3700

1350

0

SEL50

6420

4200

1500

unpacking

Inspect this unit before it is used. 
Occasionally, products are damaged 
during shipment. If the pump or 
components are damaged, return 
the unit to the place of purchase for 
replacement. Failure to do so could 
result in serious injury or death.

Safety Guidelines

This manual contains information 
that is very important to know and 
understand. This information is 
provided for SAFETY and to PREVENT 
EQUIPMENT PROBLEMS. To help 
recognize this information, observe the 
following symbols.

 

Danger indicates  

  an imminently 

hazardous situation which, if not 
avoided, WILL result in death or serious 
injury.

 

Warning indicates  

  a potentially 

hazardous situation which, if not 
avoided, COULD result in death or 
serious injury.
 

Caution indicates  

  a potentially 

hazardous situation which, if not 
avoided, MAY result in minor or 
moderate injury.
 

Notice indicates  

  important 

information, that if not followed, may 
cause damage to equipment.

General Safety Information

CALIfORNIA PROPOSItION 65

 

This product or its  

  power cord contains 

chemicals known to the State of 
California to cause cancer and birth 
defects or other reproductive harm. 
Wash hands after handling.

Summary of Contents for 330002-001





















Reviews: