background image

WARRANTY*

CHAMPION POWER EQUIPMENT

3 YEAR LIMITED WARRANTY

Warranty Qualifications

Champion Power Equipment (CPE) will register this warranty upon 
receipt of your Warranty Registration Card and a copy of your sales 
receipt from one of CPE’s retail locations as proof of purchase.
Please submit your warranty registration and your proof of purchase 
within ten (10) days of the date of purchase.

Repair/Replacement Warranty

CPE warrants to the original purchaser that the mechanical and 
electrical components will be free of defects in material and 
workmanship for a period of three years (parts and labor) from 
the original date of purchase and 270 days (parts and labor) for 
commercial and industrial use. Transportation charges on product 
submitted for repair or replacement under this warranty are the sole 
responsibility of the purchaser. This warranty only applies to the 
original purchaser and is not transferable.

Do Not Return The Unit To The Place Of Purchase

Contact CPE’s Technical Service and CPE will troubleshoot any issue 
via phone or e-mail. If the problem is not corrected by this method, 
CPE will, at its option, authorize evaluation, repair or replacement 
of the defective part or component at a CPE Service Center. CPE 
will provide you with a case number for warranty service. Please 
keep it for future reference. Repairs or replacements without prior 
authorization, or at an unauthorized repair facility, will not be covered 
by this warranty.

Warranty Exclusions

This warranty does not cover the following repairs and equipment:

Normal Wear

Products with mechanical and electrical components need periodic 
parts and service to perform well. This warranty does not cover repair 
when normal use has exhausted the life of a part or the equipment as a 
whole.

Installation, Use and Maintenance

This warranty will not apply to parts and/or labor if the product is 
deemed to have been misused, neglected, involved in an accident, 
abused, loaded beyond the product’s limits, modified, installed 
improperly or connected incorrectly to any electrical component.  
Normal maintenance is not covered by this warranty and is not 
required to be performed at a facility or by a person authorized by 
CPE.

Other Exclusions

This warranty excludes:

 

Cosmetic defects such as paint, decals, etc.

 

Wear items such as filter elements, o-rings, etc.

 

Accessory parts such as starting batteries, and storage covers.

 

Failures due to acts of God and other force majeure events 
beyond the manufacturer’s control.

 

Problems caused by parts that are not original Champion Power 
Equipment parts.

When applicable, this warranty does not apply to products used for 
prime power in place of a utility.

Limits of Implied Warranty and Consequential Damage

Champion Power Equipment disclaims any obligation to cover 
any loss of time, use of this product, freight, or any incidental 
or consequential claim by anyone from using this product. THIS 
WARRANTY AND THE ATTACHED U.S. EPA, CARB and/or ECCC 
EMISSION CONTROL SYSTEM WARRANTIES (WHEN APPLICABLE) 
ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, 
INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR 
A PARTICULAR PURPOSE. 
A unit provided as an exchange will be subject to the warranty of the 
original unit. The length of the warranty governing the exchanged 
unit will remain calculated by reference to the purchase date of the 
original unit.
This warranty gives you certain legal rights which may change from 
state to state or province to province. Your state or province may also 
have other rights you may be entitled to that are not listed within this 
warranty.

Contact Information
Address

Champion Power Equipment, Inc.
Customer Service
12039 Smith Ave.
Santa Fe Springs, CA 90670 USA
www.championpowerequipment.com

Customer Service

Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)
Toll Free: 1-877-338-0999
[email protected]
Fax no.: 1-562-236-9429

Technical Service

Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)
Toll Free: 1-877-338-0999
[email protected]
24/7 Tech Support: 1-562-204-1188

WARRANTY

* Except  as  otherwise  stipulated  in  any  of  the  following  enclosed  Emission  Control  System  Warranties  (when  applicable)  for  the  Emission  Control  System:  U.S. 

Environment Protection Agency (EPA), California Air Resources Board (CARB) and/or Environment and Climate Change Canada (ECCC). Whichever warranty applies 
for the longer period, either this 3 year limited warranty or the applicable Emission Control System Warranty, shall supersede the other.

Summary of Contents for 100401


































Reviews: