background image

17

Make life easier with 

these handy accessories. 

The perfect extras for convenience, security and safety.

1

1

2

4

3

5

6

myQ Connectivity Kit

C828AU774R

Four Button Car Visor 

Remote Control 

E964M

Four Button Wireless 

Wall Mount Remote 

Control 

E148M

myQ Remote LED Light

827AU

Water Resistant 

Four Button Remote

E980M

Wireless Security Keypad

E840M

6

3

5

4

2

2

29119 - JUNE 2021 

Upgrade to myQ Smart Garage Control 

with the myQ Connectivity Kit to monitor 

and control your garage door away from 

home through the myQ App.* Kit includes 

Safety IR Beams and myQ Gateway.

Smart lighting 

to brighten the 

whole garage.

Easily attaches to 

the wall to control 

both S and 

S 2.0 devices.

Slimline visor 

remote works with 

any S and 

S 2.0 devices.

Compact water resistant

remote control designed 

for any S and 

S 2.0 devices.

Convenient access 

without using a 

remote control or key.

FIND YOUR LOCAL RETAILER

       

Scan to discover more…

Australia

New Zealand

* Additional purchase of myQ Connectivity Kit required to enable myQ functionality.

† IP65 Protection against low-pressure water jets from any angle. See gomerlin.com.au or gomerlin.co.nz for more information.

OPERATION AND MAINTENANCE

Summary of Contents for RollerLift Plus





















Reviews: