Chamberlain Power Drive Security+ 7520S Owner'S Manual Download

Page: 24 / 40

Header Wall

Vertical
Centerline of
Garage Door

Finished Ceiling

Optional
Placement
of Door
Bracket

Header

Bracket

Door
Bracket

2x4 Support

For a door with no exposed framing,
or for the optional installation, use
lag screws 5/16"x1-1/2" (Not Provided)
to fasten door bracket.

METAL DOOR

Top of Door
(Inside
Garage)

Door
Bracket

Optional
Placement

Top Edge
of Door

Self-Threading
Screw
1/4"-14x5/8"

Door
Bracket

Top of Door
(Inside
Garage)

Carriage Bolt
5/16"x2"
(Not Provided)

Optional
Placement

Lock
Washer
5/16"

Nut
5/16"-18

Top Edge
of Door

WOOD DOOR

HORIZONTAL AND VERTICAL
REINFORCEMENT IS NEEDED
FOR LIGHTWEIGHT GARAGE
DOORS (FIBERGLASS,
ALUMINUM, STEEL, DOORS
WITH GLASS PANEL, ETC.).
(NOT PROVIDED)

ONE-PIECE DOORS

Please read and comply with the warnings and
reinforcement instructions on the previous page.
They apply to one-piece doors also.

• Center the door bracket on the top of the door, in

line with the header bracket as shown. Mark either
the left and right, or the top and bottom holes.

•

Metal Doors:

Drill 3/16" pilot holes and fasten the

bracket with the 1/4"-14x5/8" self-threading screws
provided.

•

Wood Doors:

Drill 5/16" holes and use 5/16"x2"

carriage bolts, lock washers and nuts (not
provided) or 5/16"x1-1/2" lag screws (not provided)
depending on your installation needs.

NOTE:

The door bracket may be installed on the top

edge of the door if required for your installation.
(Refer to the dotted line optional placement drawing.)

Self-Threading Screw
1/4"-14x5/8"

HARDWARE SHOWN

ACTUAL SIZE

Summary of Contents for Power Drive Security+ 7520S









































Search results

Summary of Contents for Power Drive Security+ 7520S

Reviews:

Related manuals for Power Drive Security+ 7520S

Brands by name

Popular brands

Chamberlain Power Drive Security+ 7520S, Owner'S Manual

Search results

Summary of Contents for Power Drive Security+ 7520S

Reviews:

Related manuals for Power Drive Security+ 7520S

Brands by name

Popular brands