Chamberlain Power Drive Security+ 7520S Owner'S Manual Download | Manualshive

Page: 6 / 40

background image

6

2-Conductor Bell Wire
White & White/Red

Chain and Cable in
Dispensing Carton

Curved Door
Arm Section

Straight Door
Arm Section

Safety Labels

and

Literature

Hanging Brackets

Door Bracket

(2) Safety Reversing Sensors
(1 Sending Eye and 1 Receiving Eye)
with 2-Conductor White & White/Black
Bell Wire attached

Safety Sensor
Bracket (2)

Motor Unit with 2 Light Lenses

Header Bracket

Idler Pulley

"U" Bracket

Trolley

Chain Spreader

Rail
Center/Back
Sections

Rail
Front (header)
Section

Lighted Door Control Button
with (2) screws 6ABx1-1/2"

SECURITY

✚

Single-Button Remote Control (2)

Your garage door opener is packaged in one carton
which contains the motor unit and all parts illustrated
below. Accessories will depend on the model
purchased. If anything is missing, carefully check the

packing material. Parts may be stuck in the foam.
Hardware for assembly and installation is shown on
the next page. Save the carton and packing material
until installation and adjustment is complete.

Carton Inventory

«
...
4
5
6
7
8
...
»

Summary of Contents for Power Drive Security+ 7520S









































Reviews:

No comments

Related manuals for Power Drive Security+ 7520S

Brand: Wayne-Dalton Pages: 24

Brand: tau Pages: 44

Brand: Daspi Pages: 16

Brand: Daspi Pages: 14

Brand: Motorline professional Pages: 14

Brand: JOYTECH Pages: 26

Brand: RIB Pages: 60

Brand: Salton Pages: 21

Brand: Polaris Automatic Gate Operators Pages: 43

Brand: Grifco Pages: 24

Brand: tau Pages: 8

Right Angle CN762

Brand: Rival Pages: 4

Brand: Hamilton Beach Pages: 20

Brand: CAME Pages: 24

Brand: CAME Pages: 32

RapidCoil RC300 Series

Brand: Raynor Pages: 39

Brand: FERMOD Pages: 30

Brand: Accessmatic Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands