background image

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of SEVERE INJURY or DEATH:

WARNING

WARNING

1. READ AND FOLLOW ALL WARNINGS AND

INSTRUCTIONS.

2. ALWAYS keep transmitters out of reach of children.

NEVER permit children to operate or play with the

wireless wall button, multi-function door control or

transmitters.

3. ONLY activate the door when it can be seen clearly,

it is properly adjusted and there are no obstructions

to door travel.

4. ALWAYS keep the door in sight until completely

closed. NO ONE SHOULD CROSS THE PATH OF THE

MOVING DOOR.

5. NO ONE SHOULD GO UNDER A STOPPED,

PARTIALLY OPENED DOOR.

6. If possible, use emergency release handle to

disengage door ONLY when the door is CLOSED.

Weak or broken springs or unbalanced door could

result in an open door falling rapidly and/or

unexpectedly.

7. NEVER use emergency release handle unless the

doorway is clear of persons and obstructions.

8. After ANY adjustments are made, the safety

reversal system MUST be tested.

9. Safety reversal system MUST be tested every

month. The door MUST reverse on contact with

40mm (1 1/2”) high obstacle on the floor.

10. ALWAYS KEEP THE DOOR PROPERLY BALANCED

(see page 4). An improperly balanced door may

not reverse when required and could result in

SEVERE INJURY or DEATH.

11. ALL repairs to cables, spring assemblies and other

hardware, ALL of which are under EXTREME

tension, MUST be made by a trained door systems

technician.

12. ALWAYS disconnect electric power to the door

opener BEFORE making ANY repairs or removing

covers.

13. Permanently fix the Emergency release instruction

label adjacent to the release handle.

14.

KEEP THESE INSTRUCTIONS.

EMERGENCY DOOR RELEASE

TO OPEN THE DOOR MANUALLY

The door should be fully closed if possible. Pull down on

the emergency release handle until a click noise is heard

from the unit and lift the door manually. To reconnect

the door to the opener, pull down the emergency release

handle straight down a second time until a click noise is

heard from the unit. The door will reconnect on the next

UP or DOWN operation.

NOTIC

E

Emergency
Release Handle

WARNING

To prevent possible SERIOUS INJURY or DEATH from a falling door:

• If possible, use emergency release handle to disengage door ONLY when door is CLOSED. Weak or

broken springs or unbalanced door could result in an open door falling rapidly and/or unexpectedly.

• NEVER use emergency release handle unless the doorway is clear of persons and obstructions.

ADJUSTMENT STEP 5

OPERATION

WARNING

WARNING

17

Summary of Contents for Merlin MJ3800R

























Reviews: