background image

10

INSTALLATION STEP 3

ATTACH THE EMERGENCY RELEASE ROPE

AND HANDLE

• Thread one end of the rope through the hole in the top

of the red handle so “NOTICE” reads right side up as
shown. Secure with an overhand knot at least 25mm
(1") from the end of the rope to prevent slipping.

• Thread the other end of the rope through the loop in the

emergency release cable.

• Adjust rope length so the handle is no higher than 1.8m

(6’) above the floor. Secure with an overhand knot.

NOTE: If it is necessary to cut the rope, heat seal the

cut end to prevent unraveling.

Overhand
Knot

Emergency
Release Handle

Overhand
Knot

Rope

Opener

Emergency
Release Cable

016+%

'

Warning Label

WARNING

To prevent possible SERIOUS INJURY or DEATH from
a falling door:
• If possible, use emergency release handle to

disengage door ONLY when door is CLOSED. Weak
or broken springs or unbalanced door could result in
an open door falling rapidly and/or unexpectedly.

• NEVER use emergency release handle unless the

doorway is clear of persons and obstructions.

INSTALLATION STEP 4

ELECTRICAL REQUIREMENTS

To avoid installation difficulties, do not run the opener

at this time.

To reduce the risk of electric shock, your door opener has
a grounding type plug with a third grounding pin. This plug
will only fit into a grounding type outlet. If the plug doesn’t
fit into the outlet you have, contact a qualified electrician to
install the proper outlet.

To prevent possible SERIOUS INJURY or DEATH from
electrocution or fire:
• Be sure power is not connected to the opener, and

disconnect power to circuit BEFORE removing cover.

• Door installation and wiring MUST be in

compliance with ALL electrical and building
codes.

• NEVER use an extension cord, 2-wire adaptor or

change plug in any way to make it fit outlet. Be sure
the opener is grounded.

• If the supply cord is damaged, it must be replaced by

the manufacturer or it’s service agent or similarly
qualified person in order to avoid hazard.

INSTALLATION STEP 5

RIGHT

WRONG

LOCK

LIGHT

2

1

RED

WHT

Opener

Quick-Connect Terminals

To Door Control

dry contact

com

no

INSTALLING THE MULTI-FUNCTION WALL

CONTROL

Note: any connection to your MJ3800R should be

voltage free and Normally open.

There are 2 screw terminals on the back of the multi-function
door control. Strip about 6mm of insulation from bell wire.
Separate wires enough to connect the white/red wire to R
terminal screw 1 and the white wire to W terminal screw 2.
Fasten the multi-function door control to an inside garage
wall with sheet metal screws provided. Drill 4mm holes and
use anchors if installing into plasterboard wall. A convenient
place is beside the service door and out of reach of children.
Run the bell wire up the wall and across the ceiling to the
garage door opener. Use insulated staples to secure wire.
The receiver quick connect terminals are located on the
control board. Connect the bell wire to the terminals as
follows: white/red to red and white to white.

Summary of Contents for Merlin MJ3800R

























Reviews: