Chamberlain Liftmaster Elite LA500 Installation Manual Download Page 22 | Manualshive

Page: 22 / 60

background image

20

STEP 8

POWER WIRING

The standard control box can be wired for either 120 Vac or 240 Vac.
Factory default is 120 Vac. The Large Metal Control Box (XLM) can be
wired for 120 Vac (default).

The batteries are charged in the circuit by the toroid transformer,
plug-in transformer, or the solar panels. Main power supply and
control wiring MUST be run in separate conduits.

SOLAR APPLICATIONS: For solar applications refer to Solar Panels
section in the Appendix. Follow the directions according to your
application.

NOTE:

If using an external receiver use shielded wire for the connections

or mount the receiver away from the operator to avoid interference with
the operator.

STANDARD CONTROL BOX

1. Turn off the AC power from the main power source circuit breaker.

2. Run the AC power wires to the control box.

3. Remove the toroid assembly from the control box by loosening the

four screws and lifting the assembly up and out.

4. Ensure the 120/240 plug is connected to either the 120 or 240 Vac

connector on the EMI board depending on your application. Factory
default is 120 Vac.

5. Connect the ground wire to the ground screw on the back of the

toroid assembly.

6. Connect the white wire from the toroid assembly to NEUTRAL using

a wire nut.

7. Connect the black wire from the toroid assembly to HOT using a

wire nut.

8. Replace the toroid assembly and tighten the four screws. Ensure the

wires are not pinched.

9. Plug the J15 plug into the control board. The control board will

power up.

NOTE:

You may see a small spark when plugging the J15

plug into the board.

10. Turn ON AC power to the operator.

NOTE:

Use copper conductors ONLY.

Toroid
Assembly

STANDARD CONTROL BOX

J15 Plug

(back view of toroid assembly)

NEUTRAL

HOT

GROUND

White

Black

(incoming power wires)

240 Vac
Connector

120 Vac
Connector

Ground
Screw

INSTALLATION

OPERATOR POWER SOURCE

120 VAC

Wire Gauge 14

350 feet (107 m)

Wire Gauge 12

525 feet (160 m)

Wire Gauge 10

850 feet (259 m)

OR

240 VAC

Wire Gauge 14

1,150 feet (351 m)

Wire Gauge 12

1,850 feet (564 m)

Wire Gauge 10

2,950 feet (899 m)

«
...
20
21
22
23
24
...
»

Summary of Contents for Liftmaster Elite LA500





























































Reviews:

No comments

Related manuals for Liftmaster Elite LA500

Brand: Arrow Pages: 20

Brand: RAMSET Pages: 18

Brand: XMETRO Pages: 13

Brand: FAAC Pages: 36

Brand: Chamberlain Pages: 24

Marantec Control 44

Brand: Deltadoors Pages: 52

EaziClean BCO-50

Brand: Lincoln Redco Pages: 2

Brand: Xtreme Garage Pages: 2

Brand: CAME Pages: 20

Brand: Rosle Pages: 32

Brand: Chamberlain Pages: 72

Brand: Beninca Pages: 12

Brand: KING Pages: 44

Brand: CAME Pages: 20

ULTRA SAFETY SIGNAL 2595RGD

Brand: Raynor Pages: 32

SCARABEO Series

Brand: quiko Pages: 24

Brand: ZAUN24 Pages: 16

Brand: Raynor Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands