background image

4

GATE CONSTRUCTION INFORMATION

SAFETY

1.  

GENERAL REQUIREMENTS

1.1 

 Gates shall be constructed in accordance with the provisions 
given for the appropriate gate type listed, refer to ASTM F2200 for 
additional gate types.

1.2 

 Gates shall be designed, constructed and installed to not fall over 
more than 45 degrees from the vertical plane, when a gate is 
detached from the supporting hardware.

1.3 

 Gates shall have smooth bottom edges, with vertical bottom 
edged protrusions not exceeding 0.50 inches (12.7 mm) when 
other than the exceptions listed in ASTM F2200.

1.4 

 The minimum height for barbed tape shall not be less than 8 feet 
(2.44 m) above grade and for barbed wire shall not be less than 6 
feet (1.83 m) above grade.

1.5 

 An existing gate latch shall be disabled when a manually operated 
gate is retrofitted with a powered gate operator.

1.6 

 A gate latch shall not be installed on an automatically operated 
gate.

1.7 

 Protrusions shall not be permitted on any gate, refer to ASTM 
F2200 for Exceptions.

1.8 

 Gates shall be designed, constructed and installed such that their 
movement shall not be initiated by gravity when an automatic 
operator is disconnected, in accordance with the following.

1.8.1   Vehicular horizontal slide gate. Shall not result in continuous, 

unimpeded movement in either lineal direction of its travel.

1.8.2   Vehicular horizontal swing gate. Shall not result in continuous, 

unimpeded movement in either direction along the arc of its path 
of travel.

1.9 

 For pedestrian access in the vicinity of an automated vehicular 
gate, a separate pedestrian gate shall be provided. The pedestrian 
gate shall be installed in a location such that a pedestrian shall 
not come in contact with a moving vehicular access gate. A 
pedestrian gate shall not be incorporated into an automated 
vehicular gate panel.

2.  

SPECIFIC APPLICATIONS

2.1 

 Any non-automated gate that is to be automated shall be 
upgraded to conform to the provisions of this specification.

2.2 

 This specification shall not apply to gates generally used for 
pedestrian access and to vehicular gates not to be automated.

2.3 

 Any existing automated gate, when the operator requires 
replacement, shall be upgraded to conform to the provisions of 
this specification in effect at that time.

3.  

VEHICULAR HORIZONTAL SLIDE GATES

3.1 

 The following provisions shall apply to Class I, Class II and Class 
III vehicular horizontal slide gates:

3.1.1   All weight bearing exposed rollers 8 feet (2.44 m), or less, above 

grade shall be guarded or covered.

Vehicular gates should be installed in accordance with ASTM F2200: Standard Specification for Automated Vehicular Gate Construction. For a copy, 
contact ASTM directly at 610-832-9585 or www.astm.org.

3.1.2   All openings shall be designed, guarded, or screened from the 

bottom of the gate to the top of the gate or a minimum of 72 in. 
(1.83 m) above grade, whichever is less, to prevent a 2 1⁄4 in. 
(57 mm) diameter sphere from passing through the openings 
anywhere in the gate, and in that portion of the adjacent fence 
that the gate covers in the open position. The gate panel shall 
include the entire section of the moving gate,including any back 
frame or counterbalance portion of the gate.

3.1.3   A gap, measured in the horizontal plane parallel to the roadway, 

between a fixed stationary object nearest the roadway, (such as a 
gate support post) and the gate frame when the gate is in either 
the fully open position or the fully closed position, shall not 
exceed 2 1/4 inches (57 mm), refer to ASTM F2200 for Exception.

3.1.4   Positive stops shall be required to limit travel to the designed fully 

open and fully closed positions. These stops shall be installed at 
either the top of the gate, or at the bottom of the gate where such 
stops shall horizontally or vertically project no more than is 
required to perform their intended function.

3.1.5   All gates shall be designed with sufficient lateral stability to 

assure that the gate will enter a receiver guide, refer to ASTM 
F2200 for panel types.

3.2 

 The following provisions shall apply to Class IV vehicular 
horizontal slide gates:

3.2.1   All weight bearing exposed rollers 8 feet (2.44 m), or less, above 

grade shall be guarded or covered.

3.2.2   Positive stops shall be required to limit travel to the designed fully 

open and fully closed positions. These stops shall be installed at 
either the top of the gate, or at the bottom of the gate where such 
stops shall horizontally or vertically project no more than is 
required to perform their intended function.

4.  

VEHICULAR HORIZONTAL SWING GATES

4.1 

 The following provisions shall apply to Class I, Class II and Class 
III vehicular horizontal swing gates:

4.1.1   Gates shall be designed, constructed and installed so as not to 

create an entrapment area between the gate and the supporting 
structure or other fixed object when the gate moves toward the 
fully open position, subject to the provisions in 4.1.1.1 and 
4.1.1.2.

4.1.1.1  The width of an object (such as a wall, pillar or column) covered 

by a swing gate when in the open position shall not exceed 4 
inches (102 mm), measured from the center line of the pivot 
point of the gate, refer to ASTM F2200 for exception.

4.1.1.2  Except for the zone specified in Section 4.1.1.1, the distance 

between a fixed object such as a wall, pillar or column, and a 
swing gate when in the open position shall not be less than 16 
inches (406 mm), refer to ASTM F2200 for exception.

4.2 

 Class IV vehicular horizontal swing gates shall be designed, 
constructed and installed in accordance with security related 
parameters specific to the application in question.

Summary of Contents for Liftmaster Elite LA500





























































Reviews: