Chamberlain Liftmaster Elite LA500 Installation Manual Download Page 11

Page: 11 / 60

• To AVOID damaging gas, power or other underground utility lines,

contact underground utility locating companies BEFORE digging
more than 18 inches (46 cm) deep.

• ALWAYS wear protective gloves and eye protection when changing

the battery or working around the battery compartment.

INSTALLATION

•

The operator can be mounted on top of the gate frame.

•

The operator must be installed at least 12 inches from the ground.

INSTALLATION TIPS

•

Weld a horizontal bar across entire gate on any installation for

strength. Make sure that the operator is mounted level or it will not
function properly.

•

Make sure there is slack in the operator cable.

DO's

DON'Ts

•

DO NOT install upside down.

•

DO NOT install next to sprinklers or any area that may expose the

bottom of operator to water.

•

DO NOT install on uphill or downhill gates.

•

DO NOT install on ANY pedestrian passageways, doorways, or gates.

•

DO NOT over-bend the operator cable. Doing this will cause the wires

to eventually break.

•

DO NOT weld the crossbar on just a few pickets, or they could bend.

Operator

Cable

Summary of Contents for Liftmaster Elite LA500




























































Search results

Summary of Contents for Liftmaster Elite LA500

Reviews:

Related manuals for Liftmaster Elite LA500

Brands by name

Popular brands

Chamberlain Liftmaster Elite LA500, Installation Manual

Search results

Summary of Contents for Liftmaster Elite LA500

Reviews:

Related manuals for Liftmaster Elite LA500

Brands by name

Popular brands