Chamberlain Liftmaster Elite LA500 Installation Manual Download Page 50

Page: 50 / 60

APPENDIX

STEP 8 continued...

SOLAR PANEL(S)

WIRE THE SOLAR PANELS

1. Connect the red wire (+) from one solar panel to the black wire (-) of

the other solar panel.

2. Connect the shorter red wire (+) from the J15 plug (new wire

harness) labeled DC Power to the red wire on one solar panel.

3. Connect the shorter black wire (-) from the J15 plug (new wire

harness) labeled DC Power to the black wire from the other solar
panel.

INSTALL THE SOLAR PANEL

1. Position solar bracket on mounting surface. Mark and drill holes.

2. Insert two bolts into the track located on the back of the solar

panel(s).

3. Slide bolts in track away from bolt hole and align both bolts.

4. Secure solar panel(s) to solar bracket using two washered nuts.

5. Secure solar panel(s) assembly to mounting surface using appropriate

hardware.

Mounting Surface

Mounted Panel
Must Face South

DIAGNOSTICS

J15

+ -
BATT

- +

POWER

Red
Wire (+)

Black Wire (-)

Red
Wire (+)

Black
Wire (-)

Solar Panels

J15 Plug
(new wire
harness Model
K94-37236)

–

20W Solar panel

installation

40W Solar panel

installation

60W Solar panel

installation

Summary of Contents for Liftmaster Elite LA500




























































Search results

Summary of Contents for Liftmaster Elite LA500

Reviews:

Related manuals for Liftmaster Elite LA500

Brands by name

Popular brands

Chamberlain Liftmaster Elite LA500, Installation Manual

Search results

Summary of Contents for Liftmaster Elite LA500

Reviews:

Related manuals for Liftmaster Elite LA500

Brands by name

Popular brands