!DJUST THE (ANDING AND ,IMITS
4O REDUCE THE RISK OF 3%6%2% ).*529 OR $%!4(
z
7ITHOUT A PROPERLY INSTALLED SAFETY REVERSAL SYSTEM PERSONS
PARTICULARLY SMALL CHILDREN COULD BE 3%2)/53,9 ).*52%$ OR
+),,%$ BY A MOVING GATE
z
4OO MUCH FORCE ON GATE WILL INTERFERE WITH PROPER OPERATION OF SAFETY
REVERSAL SYSTEM
z
.%6%2 INCREASE FORCE BEYOND MINIMUM AMOUNT REQUIRED TO MOVE
GATE
z
.%6%2 USE FORCE ADJUSTMENTS TO COMPENSATE FOR A BINDING OR STICKING
GATE
z
)F ONE CONTROL FORCE OR TRAVEL LIMITS IS ADJUSTED THE OTHER CONTROL
MAY ALSO NEED ADJUSTMENT
z
!FTER !.9 ADJUSTMENTS ARE MADE THE SAFETY REVERSAL SYSTEM -534 BE
TESTED 'ATE -534 REVERSE ON CONTACT WITH AN OBJECT
3LIDE GATE OPERATORS WITH THE NEW CONTROL BOARD REQUIRE A
MINIMUM OF TWO
EXTERNAL MONITORED ENTRAPMENT PROTECTION DEVICES TO FUNCTION ONE IN THE OPEN
DIRECTION AND ONE IN THE CLOSE DIRECTION
4HE ADJUSTMENTS ALLOW YOU TO SET WHERE THE GATE WILL STOP IN THE OPEN AND
CLOSE POSITION 4HE FORCE IS ADJUSTED AUTOMATICALLY WHEN YOU SET THE
LIMITS BUT SHOULD BE FINE TUNED USING THE &/2#% DIAL ON THE CONTROL
BOARD REFER TO &ORCE $IAL SECTION 4HE 4EST "UTTONS ON THE CONTROL BOARD
WILL NOT WORK UNTIL THE HANDING IS SET &OR DUAL GATE APPLICATIONS THE
LIMITS WILL HAVE TO BE SET FOR EACH OPERATOR 4HE GATE -534 BE ATTACHED TO
THE OPERATOR BEFORE SETTING THE LIMITS AND FORCE
/0%. 2)'(4
)F THE OPERATOR IS INSTALLED ON THE RIGHT SIDE OF THE DRIVEWAY
WHEN LOOKING OUT OF THE PROPERTY THE GATE SHOULD BE SET TO OPEN RIGHT
/0%. ,%&4
)F THE OPERATOR IS MOUNTED ON THE LEFT SIDE OF THE DRIVEWAY
WHEN LOOKING OUT OF THE PROPERTY THE GATE SHOULD BE SET TO OPEN LEFT
3ET THE HANDING
4O SET THE INITIAL HANDING OF THE OPERATOR MAKE SURE THAT BOTH /0%.
,%&4 AND /0%. 2)'(4 ,%$S ARE FLASHING )F THEY ARE NOT FLASHING
PRESS AND HOLD BOTH THE /0%. ,%&4 AND /0%. 2)'(4 HANDING
BUTTONS UNTIL BOTH HANDING ,%$S START TO FLASH AND THE OPERATOR
BEEPS
0RESS AND RELEASE EITHER THE /0%. 2)'(4 OR /0%. ,%&4 BUTTON
DEPENDING ON WHICH DIRECTION THE GATE SHOULD OPEN 4HE
CORRESPONDING HANDING ,%$ WILL TURN SOLID
4O RELEARN THE HANDING REPEAT THE STEPS ABOVE
3ET THE LIMITS
-AKE SURE THE GATE IS CLOSED
0RESS AND RELEASE THE /0%. TEST BUTTON TO OPEN THE GATE
0RESS THE 34/0 TEST BUTTON WHEN THE DESIRED /0%. LIMIT IS REACHED
!DJUST THE LIMIT NUT OR CAM SO IT MAKES CONTACT WITH THE /0%. LIMIT
SWITCH AT THIS POSITION )F THE GATE STOPS EARLY MOVE THE LIMIT NUT OR
CAM TO ALLOW FOR ADDITIONAL TRAVEL
0RESS AND RELEASE THE #,/3% TEST BUTTON TO CLOSE THE GATE
0RESS THE 34/0 TEST BUTTON WHEN THE DESIRED #,/3% LIMIT IS
REACHED !DJUST THE LIMIT NUT OR CAM SO IT MAKES CONTACT WITH THE
#,/3% LIMIT SWITCH AT THIS POSITION )F THE GATE STOPS EARLY MOVE THE
LIMIT NUT TO ALLOW FOR ADDITIONAL TRAVEL
3ET THE &ORCE AND 2UN $ISTANCE
0RESS THE /0%. TEST BUTTON TO OPEN THE GATE
0RESS AND RELEASE BOTH THE /0%. ,%&4 AND /0%. 2)'(4 HANDING
BUTTONS
0RESS THE HANDING BUTTON BELOW THE SOLID ,%$
2UN THE OPERATOR ONE FULL CYCLE USING THE TEST BUTTONS 4HE INITIAL
FORCES AND RUN DISTANCE WILL BE SET DURING THIS CYCLE
CSW200
SL3000
SL585
SL595
Limit Nuts
Limit Nuts
Limit
Nuts
Limit Switches
Limit
Switches
Limit
Switches
Open Limit Switch
Limit
Cams
Close Limit Switch
