background image

29

CARE OF YOUR OPENER

LIMIT AND FORCE ADJUSTMENTS:

Weather conditions may cause 
some minor changes in door 
operation requiring some 
re-adjustments, particularly during 
the first year of operation.

Pages 23 and 24 refer to the limit 
and force adjustments. Only a 
screwdriver is required. Follow 
the instructions carefully.

Repeat the safety reverse test 
(Adjustment Step 3, page 25) 
after any adjustment of limits or force.

MAINTENANCE SCHEDULE

Once a Month

•  Manually operate door. If it is unbalanced or binding, call 

a trained door systems technician.

•  Check to be sure door opens and closes fully. Adjust 

limits and/or force if necessary. (See pages 23 and 24.)

•  Repeat the safety reverse test. Make any necessary 

adjustments. (See Adjustment Step 3.)

Twice a Year

•  Check chain tension. Disconnect trolley first. Adjust if 

necessary (See page 7).

Once a Year

•  Oil door rollers, bearings and hinges. The opener does 

not require additional lubrication. Do not grease the door 
tracks.

FORCE CONTROLS

1

3

9

7

5

1

3

9

7

5

LIMIT CONTROLS

KG

KG

To Open the Door Manually

The door should be fully closed if 
possible. Pull down on the 
emergency release handle and lift 
the door manually. To reconnect 
the door to the opener, press the 
door control push bar.

The 

lockout feature

 prevents the 

trolley from reconnecting 
automatically. Pull the emergency 
release handle down and back 
(toward the opener). The door can 
then be raised and lowered 
manually as often as necessary. 
To disengage the lockout feature, 
pull the handle straight down. The 
trolley will reconnect on the next 
UP or DOWN operation, either 
manually or by using the door 
control or remote.

To prevent possible SERIOUS INJURY or DEATH from a falling 
garage door:
•  If possible, use emergency release handle to disengage 

trolley ONLY when garage door is CLOSED. Weak or broken 
springs or unbalanced door could result in an open door 
falling rapidly and/or unexpectedly.

•  NEVER use emergency release handle unless garage doorway 

is clear of persons and obstructions.

•  NEVER use handle to pull door open or closed. If rope knot 

becomes untied, you could fall.

Trolley
Release 
Arm

NO

TICE

Emergency
Release 
Handle
(Pull Down)

Trolley
Release 
Arm

NOTICE

Emergency
Release Handle
(Down and Back)

LOCKOUT POSITION

MANUAL DISCONNECT 

POSITION

Summary of Contents for Elite 3575S









































Reviews: