background image

Using the Remote Control

NOTE: 

To activate the remote control functions, pull out 

the plastic pull tab protruding from the remote control 
housing.

This remote control is equipped with a proximity lighting 
feature. When moving a hand within close proximity to the 
remote control, the LED lights turn on for 3 seconds. Upon 
successful activation of a remote control button, the LED 
lights will blink rapidly.

Proximity Disable Feature

The remote control will turn off the proximity lighting 
feature if the proximity lighting is turned on 10 consecutive 
times without activation of a button. To re-enable the 
proximity lighting, simply press a button. This function 
conserves battery life.

To Control the Opener Lights

With 315MHz Security

®

 remote controls, a remote push 

button can be programmed to operate the opener lights 
without opening the door.

1.  

With the door closed,

 press and hold the remote button 

that you want to control the light.

2.  Press and hold the Light button on the Smart Control 

Panel™.

3.  Press and hold the Lock button on the Smart Control 

Panel™.

4. After the opener lights flash, release all buttons.

Test by pressing the remote push button. The opener 
lights should turn on or off but the door should not move.

28

Troubleshooting

Reduced proximity 
sensing (does not 
activate by 
touching top of 
remote control)

Check if proximity lighting is 
disabled by pressing a button.

Replace 3V2450 battery with 
same type 3V2450 coin cell.

The Proximity Sensor may be 
oversensitized. Sit remote control 
undisturbed for 60 seconds on a 
non-metallic surface. This allows 
the sensor to recalibrate itself.

Dim LED lights

Replace two 3V2016 batteries 
with same type 3V2016 coin 
cells.

No rapid LED 
blinking after 
pressing a button

Replace two 3V2016 batteries 
with same type 3V2016 coin 
cells.

PROBLEM

SOLUTION

NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this 
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the 
battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the 
following two conditions: (1) this device may not cause harmful interference, and (2) this device 
must accept any interference received, including interference that may cause undesired operation.

The Remote Control Batteries

The 3V2016 lithium 
batteries for the opener and 
LED lights (marked “LED 
and Opener Battery”) 
should last 5 years. The 
3V2450 lithium battery for 
the proximity lighting 
(marked “Proximity Battery”) 
should last 1-2 years.

To replace the batteries, 
remove the two screws and 
open the remote control 
housing. Push the battery 
out of the holder for removal.
Insert replacement batteries 
positive side up (+)
Dispose of old batteries properly.
Replace the batteries with only 
3V2016 or 3V2450 coin cell batteries.

CAUTION:

 Do not bend spring contact. 

If bent, the proximity sensor will not work.

To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
To reduce risk of fire, explosion or chemical burn:
• Replace ONLY with 3V2016 or 3V2450 coin batteries.
•  Do NOT recharge, disassemble, heat above 212°F (100°C ) 

or incinerate.

Proximity
Battery

LED and
Opener
Batteries

Spring
Contact

Summary of Contents for Elite 3575S









































Reviews: