background image

14

INSTALLATION STEP 7

Install the Light 

•  

Press the release tabs on both sides of lens. Gently 
rotate lens back and downward until the lens hinge is in 
the fully open position. Do not remove the lens.

•  

Install up to a 100 watt maximum light bulb in each 
socket. The light will turn ON and remain lit for 
approximately 4-1/2 minutes when power is connected. 
Then the lights will turn OFF.

•  

Reverse the procedure to close the lens.

•  

Use A19, standard neck garage door opener bulbs for 
replacement.

NOTE:

 

Use only standard light bulbs. The use of short 

neck or speciality light bulbs may overheat the endpanel or 
light socket.

INSTALLATION STEP 8

Attach the Emergency Release Rope 
and Handle

•  

Thread one end of the rope through the hole in the top 
of the red handle so “NOTICE” reads right side up as 
shown. Secure with an overhand knot at least 1" 
(2.5 cm) from the end of the rope to prevent slipping.

•  

Thread the other end of the rope through the hole in the 
release arm of the outer trolley.

•  

Adjust rope length so the handle is 6 feet (1.83 m) 
above the floor. Ensure that the rope and handle clear 
the tops of all vehicles to avoid entanglement. Secure 
with an overhand knot.

NOTE: 

If it is necessary to cut the rope, heat seal the cut 

end with a match or lighter to prevent unraveling.

Trolley

NOTICE

Overhand
Knot

Emergency
Release Handle

Rope

Trolley
Release Arm

To prevent possible SERIOUS INJURY or DEATH from a falling 
garage door:
•  If possible, use emergency release handle to disengage 

trolley ONLY when garage door is CLOSED. Weak or broken 
springs or unbalanced door could result in an open door 
falling rapidly and/or unexpectedly.

•  NEVER use emergency release handle unless garage 

doorway is clear of persons and obstructions.

•  NEVER use handle to pull door open or closed. If rope knot 

becomes untied, you could fall.

Lens
Hinge

100 Watt (Max)
Standard Light Bulb

Release Tab

100 Watt (Max)
Standard Light Bulb

To prevent possible OVERHEATING of the endpanel or light 
socket:
•   DO NOT use short neck or specialty light bulbs.
•   DO NOT use halogen bulbs. Use ONLY incandescent.
To prevent damage to the opener:
•   DO NOT use bulbs larger than 100W.
•  ONLY use A19 size bulbs.

Summary of Contents for Elite 3575S









































Reviews: