Radikal G30 v.2
Page 22
REAR SIDEFRAME (RIGHT)
CNM3x8BHCS
CNM3x25BHCS
CNLR1014
CNBB0730
3x8x3.5
CNM3x12BHCS
CNBB812F
CNM3x10BHCS
Canopy Standoff(
机头罩支架
)
Button Head Cap Screw(
圆头内六角螺丝
)M3x25
CNM3x25BHCS
M3 Linkage Ball(
球头螺丝
)
CNLR1014
Bell Crank(
左右控制臂
)
Bearing(
滚珠轴承
)3x7x3
CNBB0730
Bellcrank Spacer(
垫片
)3x8x3.5
Elevator Lever Flange Bearing(
带边滚珠轴承
)
CNBB812F
Button Head Cap Screw(
圆头内六角螺丝
)M3x8
CNM3x8BHCS
Aluminum Post(
铝柱
)
Control Arm(
控制臂
)
Button Head Cap Screw(
圆头内六角螺丝
)M3x12
CNM3x12BHCS
Bellcrank Spacer(
垫片
)3x5x7
HI6031G
HI6031G
HI6031G
HW6125B
HI6031S
HI6032GB
Button Head Cap Screw(
圆头内六角螺丝
)M3x12
CNM3x12BHCS
Fuel Tank Rubber Pad(
油箱橡胶垫
)
HI6139B
Reinforcement Plate Right (
右补强板
)
HW6114G3
Main Frames Right Rear Carbon (
左右后侧板
)
Button Head Cap Screw(
圆头内六角螺丝
)M3x10
CNM3x10BHCS
4
1
2
3
4
5
6
2
2
2
2
No.
Description
Qty
Part #
8
7
8
9
10
2
1
9
1
11
12
1
2
13
14
15
17
18
19
2
4
1
2
1
2
16
1
Button Head Cap Screw(
圆头内六角螺丝
)M3x12
CNM3x12BHCS
Machined Washer(
螺丝护套
)
CN2218S
20
3
3x5x1.8 Steel(3x5x1.8
钢套
)
1
2
3
6
5
4
7
8
9
10
11
14
13
15
16
19
20
18
17
12
BAG 2
When installing the elevator bellcrank,
make sure to apply medium CA to the
M3x12 button head cap screw.
Note: If you experience any bind-
ing in the bellcranks after assem-
bly, please use the supplied 3mm
washer between one of the 3x7x3
bearings and the inner spacer.
Assemble the aileron bellcranks by first pressing in the 3x7x3 bear-
ing followed by the 3x5x7.5 spacer. Install the remaining bearing
along with the metal balls. It is easier to thread the M3 linkage balls
into the plastic bell cranks if you use an available M3 screw to make
threads. Apply medium CA to the linkage balls. Once you have the
aileron bell cranks built, install the right rear frame and apply me-
dium threadlock to the M3x8 button head screws and tighten onto
the skeletal support frame. Apply medium threadlock to the M3x25
button head cap screws and install the aileron bell cranks onto the
aluminum post.
HI6116RC3GA
HI6116RC3G
