CENTURION SYSTEMS VERT-X Mechanical Installation Manual Download

Page: 50 / 56

page 50

www.CentSys.com

10.3.6. Step 6: Check the Installation if you have the Metal Template

FIGURE 51. GATE CLOSED (METAL TEMPLATE FITTED)

Metal template

Wall Bracket

Custom

Bracket

Gate Bracket

Gate in closed position

Pin

With the metal template mounted

to the gate as per Section 10.6.2.,

swing the gate leaf to the open

position. If it is possible to open the

gate to the required open position

without the template fouling against

the gate pillar or gate, and the Gate

Bracket Pin travels within the slot of

the metal template without fouling,

then the installation of the brackets

is deemed to be correct.

FIGURE 52. GATE OPEN

(METAL TEMPLATE FITTED)

Metal

template

Wall Bracket

Custom

Bracket

Gate

Pin

ECTION

OPERA

TOR

INS

TALLATION

OUTW

ARD

OPENING

GATE

If you do not have the Metal

Template, make sure that

the spot welds are sufficient

to take a significant load

as back-driving the unit

through the gearbox in the

override condition requires a

large force when the unit is

new out of the box.

Summary of Contents for VERT-X

























































Search results

Summary of Contents for VERT-X

Reviews:

Related manuals for VERT-X

Brands by name

Popular brands

CENTURION SYSTEMS VERT-X, Mechanical Installation Manual

Search results

Summary of Contents for VERT-X

Reviews:

Related manuals for VERT-X

Brands by name

Popular brands