CENTURION SYSTEMS VERT-X Mechanical Installation Manual Download

Page: 37 / 56

page 37

www.CentSys.com

9.3.6. Step 6: Check the Installation if you have the Metal Template

FIGURE 32. GATE CLOSED (METAL TEMPLATE FITTED)

Metal template

Wall bracket

Gate Bracket

Gate

in closed

position

Pin

With the Metal Template mounted

to the gate as per Section 9.3.6.2.,

swing the gate leaf to the open

position. If it is possible to open the

gate to the required open position

without the template fouling against

the gate pillar or gate, and the Gate

Bracket Pin travels within the slot of

the Metal Template without fouling,

then the installation of the brackets

is deemed to be correct.

If you do not have the Metal

Template, make sure that

the spot welds are sufficient

to take a significant load

as back-driving the unit

through the gearbox in the

override condition requires a

large force when the unit is

new out of the box.

FIGURE 33. GATE OPEN

(METAL TEMPLATE FITTED)

Metal template

Wall Bracket

Gate Bracket

Pin

OPERA

TOR

INS
TALLATION

INW

ARD

OPENING

GA
TE

ECTION

Summary of Contents for VERT-X

























































Search results

Summary of Contents for VERT-X

Reviews:

Related manuals for VERT-X

Brands by name

Popular brands

CENTURION SYSTEMS VERT-X, Mechanical Installation Manual

Search results

Summary of Contents for VERT-X

Reviews:

Related manuals for VERT-X

Brands by name

Popular brands