CENTURION SYSTEMS VERT-X Mechanical Installation Manual Download

Page: 41 / 56

page 41

www.CentSys.com

Values- A, B, & C are measured from the gate hinge point.

Value- D is measured from the gate hinge point centre line.

Value-E is measured from the gate face to the Gate Bracket centre point.

With this type of operator, it is critical to choose the correct installation

position from the installation tables to ensure that the tip of the

operator does not interfere with the gate during operation.

Use the following installation tables to determine the best geometry for the installation.

VERT-X Outward Opening Geometry Tables:

90º Outward Opening Gate

100º Outward Opening Gate

E-Value

A-Value

B-Value

C-Value

D-Value

>85mm

155mm

140mm

633mm

110mm

>85mm

160mm

135mm

630mm

110 - 115mm

E-Value

A-Value

B-Value

C-Value

D-Value

>80mm

140mm

160mm

618mm

115mm

>82.5mm

150mm

628mm

115mm

>82.5mm

160mm

140mm

638mm

115mm

TABLE 8

TABLE 9

Optimum Installation

OPERA

TOR

INS
TALLATION

-OUTW

ARD

OPENING

GATE

ECTION

Summary of Contents for VERT-X

























































Search results

Summary of Contents for VERT-X

Reviews:

Related manuals for VERT-X

Brands by name

Popular brands

CENTURION SYSTEMS VERT-X, Mechanical Installation Manual

Search results

Summary of Contents for VERT-X

Reviews:

Related manuals for VERT-X

Brands by name

Popular brands