manualshive.com logo in svg

Central Machinery Industrial 97816, Set Up And Operating Instructions Manual

Share
Download
Central Machinery Industrial 97816 Set Up And Operating Instructions Manual Download Page 17

Page 17

SKU 97816

For technical questions, please call 1-800-444-3353.

ing washers.  Therefore, remove the 

Table (126), left and right Extension 

Wings (127), and set them aside.
Loosen the Hex Head Bolt (272) 

7. 

shown in the illustration below, and 

slowly slide the Geared Bearing 

Housing (271) toward the end of the 

Height Shaft (245).  Only move the 

Geared Bearing Housing a distance 

equal to the amount of misalignment 

between the Saw Blade and the Split-

ter (311), or slightly a little more (you 

can always adjust the Splitter back to 

the left with washers). 

(See Figure p.)

Tighten the Hex Head Bolt (272) se-

8. 

curely.  

(See Figure p.)

FIgurE p

HEX HEAd BOLT (272)

gEArEd BEArINg HOuSINg

(271)

9.  Moving the Geared Bearing Housing 

(271) moves the V-Belts (230) and 

Pulleys (231, 282) out of alignment, 

so adjustment of the Motor Pulley 

(231) is required.  To do so, loosen 

the Set Screw (232) in the middle 

groove of the Motor Pulley and slowly 

slide the Pulley toward the end of the 

Motor’s (234) Shaft.  Once the V-Belts 

are back in alignment, tighten the Set 

Screw securely.  

(See Figure Q.)

FIgurE Q

V-BELTS

(230)

SET SCrEW

(232)

MOTOr puLLEY

(231)

SHAFT

MOTOr

(234)

10.  Recheck the Blade Guard Assembly 

alignment to the Saw Blade and the 

Table (126) top.  If the Blade Guard 

Assembly is properly aligned re-attach 

the Table and left and right Extension 

Wings (127), making sure there is ad-

equate Saw Blade clearance through 

all Saw Blade adjustments.
Adjust the Saw Blade to 45 degrees.  

11. 

Raise and lower the Saw Blade 

through the full range.  Readjust the 

Saw Blade to 90 degrees.  Then raise 

and lower the Saw Blade through 

the full range.  

There should be no 

contact between the Saw Blade, the 

Table (126), the Table Insert (131 or 

136), or any other part of the Table 

Saw.  If there is contact, have a 

qualified service technician make 

the necessary adjustments before 

using the Table Saw.

To Adjust the 45° and 90° positive 

Stops

The Stops have been adjusted at the 

1. 

factory.  After a period of use, or after 

moving the Table Saw from one lo-

Summary of Contents for 97816



































Reviews:

No comments

Brands by name

Popular brands

Load more brands