Centa CENTAX-G Assembly And Operating Instructions Manual Download Page 47

Page: 47 / 52

Assembly and operating instructions

CENTAX-G

020G-00050…00090-F.10

M020-00009-EN

Rev. 4

CENTA Antriebe Kirschey GmbH

47 / 52

9.7.3

Removing the rubber element (1.1) with the ring (1.4)

See Fig. 6-8:



Together with the ring (1.4) and the dismantling supports remove the rubber
element (1.1) out of the installation space.

9.8

Removing the ring (1.4)

See Fig. 6-6:



Pull the ring (1.4) out of the rubber element (1.1) and remove.

9.9

Dismantling the membrane (1.2.1)

See Fig. 6-5:



Remove the membrane (1.2.1) and the ring (1.9; only at sizes
00050…00075) from the flange/hub/adapter (E/3/17).

9.10

Dismantling the adapter (17; if existing/ necessary)

See Fig. 6-4:



Loosen the screws of the connection adapter (17) and the flange/hub (E/3)
and remove.



Push the adapter (17) off/out of the centring of the flange/hub (E/3) and
remove.

9.11

Dismantling the hub (3; if existing/necessary)



Dismantle the hub (3) as appropriate for the supplied design (see installation
drawing).



Dismantling the hub with cylindrical bore and keyway, see chapter
9.11.1.



Dismantling the hub with conical oil interference fit, see chapter 9.11.2.

9.11.1

Dismantling the hub with cylindrical bore and keyway

See Fig. 6-1:



Remove the hub (3) from the shaft (A).

Summary of Contents for CENTAX-G





















































Search results

Summary of Contents for CENTAX-G

Reviews:

Related manuals for CENTAX-G

Brands by name

Popular brands

Centa CENTAX-G, Assembly And Operating Instructions Manual

Search results

Summary of Contents for CENTAX-G

Reviews:

Related manuals for CENTAX-G

Brands by name

Popular brands