Centa CENTAX-G Assembly And Operating Instructions Manual Download Page 43

Page: 43 / 52

Assembly and operating instructions

CENTAX-G

020G-00050…00090-F.10

M020-00009-EN

Rev. 4

CENTA Antriebe Kirschey GmbH

43 / 52

Care and maintenance

WARNING

Injuries can occur as a result of:



Contact with rotating parts

Before starting work at the coupling, switch off the plant and secure
against unintentional start-up.

The coupling requires low maintenance. It is possible to perform a visual
inspection during the regular scheduled maintenance intervals for the complete
unit. Every 12 months a visual inspection is strictly required.

8.1

Work to be performed

8.1.1

Cleaning the coupling



Remove any loose dirt from the coupling.

8.1.2

Visual inspection of the coupling



Inspect the coupling for cracks, chips or missing parts.



Replace faulty and missing parts.

8.1.3

Visual inspection of the rubber elements / rubber segments

IMPORTANT

Exchange the rubber elements / rubber segments in the event that:



The wear specifications given in W000-00002 are exceeded



Assess the rubber elements / rubber segments as described in CENTA
guidelines W000-00002.

8.1.4

Inspection of the screw connections



Check the tightening torque levels of all screws and if necessary, correct.

8.2

Replacing defective parts



Remove the coupling as described in chapter 9.



Replace wearing parts.



Mount the coupling as described in chapter 6.

Summary of Contents for CENTAX-G





















































Search results

Summary of Contents for CENTAX-G

Reviews:

Related manuals for CENTAX-G

Brands by name

Popular brands

Centa CENTAX-G, Assembly And Operating Instructions Manual

Search results

Summary of Contents for CENTAX-G

Reviews:

Related manuals for CENTAX-G

Brands by name

Popular brands