Cedar Summit F25720 Installation And Operating Instructions Manual Download Page 1 | Manualshive

Page: 1 / 108

background image

INSTALLATION AND OPERATING INSTRUCTIONS

LOOKOUT LODGE PLAYSET – F25720

Table of Contents

Warnings and Safe Play Instructions  .  .  .  .  .  .  .  .  .  . pg . 2
Protective Surfacing Guidelines .  .  .  .  .  .  .  .  .  .  .  .  .  .  . pg . 3
Instructions for Proper Maintenance   .  .  .  .  .  .  .  .  . pg . 4
About Our Wood – Limited Warranty  .  .  .  .  .  .  .  .  . pg . 5
Keys to Assembly Success   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . pg . 6
Part ID   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .pg . 10
Step-By-Step Instructions   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .pg . 19
Installation of I .D ./Warning Plaque  .  .  .  .  .  .Final Step

To reduce the risk of serious injury or death, you must read and

follow these instructions. Keep and refer to these instructions

often and give them to any future owner of this play set.

Manufacturer contact information provided below.

OBSTACLE FREE SAFETY ZONE -30’ 9” x 27’1” (9.37 x 8.23 m) area requires Protective Surfacing. See page 3.
MAXIMUM VERTICAL FALL HEIGHT - 6’ 7” (2.01 m)
CAPACITY - 13 Users Maximum, Ages 3 to 10; Weight Limit 110 lbs. (49.9 kg) per child.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as multi-unit residences, schools, churches,

nurseries, day cares or parks.

WARNING

10 - 12 Hrs

FOR FORT & SWING

TWO PERSON

ASSEMBLY

2-4 Hrs

10 - 12 Hrs

FOR FORT & SWING

TWO PERSON

ASSEMBLY

10 - 12 Hrs

FOR FORT & SWING

2 - 4 Hrs

TUBE SLIDE

Rev 09/28/2017

Cedar Summit by KidKraft

4630 Olin Road

Dallas, TX 75244, United States
customersupport@kidKraft

canadacustomerservice@kidkraft
Customer Service:

1(800) 933-0771 or 972 385-0100
KidKraft Netherlands BV

Olypisch Stadion 29

1076DE Amsterdam, The Netherlands

europecustomerservice@kidkraft .com
Europe Customer Service

+31 (0)20 305 8620

11'-10"

27'-1"

30'-9"

18'-9"

1
2
3
...
»

Summary of Contents for F25720













































































































Reviews:

No comments

Related manuals for F25720

Brand: Bante Instruments Pages: 6

SourceMeter 2425

Brand: Keithley Pages: 141

Brand: Lithium Grim Pages: 13

Brand: Daktronics Pages: 4

Brand: A.HABERKORN Pages: 28

Brand: Hameg Pages: 33

Brand: Anderson Pages: 60

Brand: Cyclops Lighting Pages: 11

Brand: Cameo Pages: 56

Brand: gbSoundlab Pages: 7

Brand: YOKOGAWA Pages: 2

Brand: Keithley Pages: 33

Brand: Digi-Sense Pages: 16

Brand: Chatillon Pages: 2

Brand: stilum Pages: 3

QuickTest Portable

Brand: biozoom Pages: 8

Brand: Treedental Pages: 16

Brand: Jula Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands