CD Automation REVO RT User Manual Download | Manualshive

Page: 45 / 56

background image

REVO RT

from 35A to 90A

User’s manual

45

P164 - Input selection Alarm 1 (Address ModBus 2164)
P178 - Input selection Alarm 2 (Address ModBus 2178)
P192 - Input selection Alarm 3 (Address ModBus 2192)

Selects the input connected to the alarm

0

1

2

Input 1. (

Default

for Alarm1)

Input 2. (

Default

for Alarm2)

Input 3. (

Default

for Alarm3)

Alarm 4, Alarm 5 not available

P165 - Reference SP selection for Alarm 1 (Address ModBus 2165)
P179 - Reference SP selection for Alarm 2 (Address ModBus 2179)
P193 - Reference SP selection for Alarm 3 (Address ModBus 2193)

Select reference Loop

0

1

2

SP 1. (

Default

for Alarm1)

SP 2. (

Default

for Alarm2)

SP 3. (

Default

for Alarm3)

Alarm 4 not available

P166 - Alarm 1 State Output (Address ModBus 2166)
P180 - Alarm 2 State Output (Address ModBus 2180)
P194 - Alarm 3 State Output (Address ModBus 2194)
P208 - Alarm 4 State Output (Address ModBus 2208)

Alarm 1 output contact type and intervention type

0

1

2
3
4

5

(N.O. Start) normally open, operational from start (

Default

)

(N.C. Start) normally closed, operational from start
(N.O. Threshold) operational when the alarm is reached
(N.C. Threshold) operational when the alarm is reached
(N.C. Threshold Variation) inhibited after command set change
(N.C. Threshold Variation) inhibited after command set change

P167 - Hysteresis Alarm 1 (Address ModBus 2167)
P181 - Hysteresis Alarm 2 (Address ModBus 2181)
P195 - Hysteresis Alarm 2 (Address ModBus 2195)
P209 - Hysteresis Alarm 4 (Address ModBus 2209)

Hysteresis alarme

-10000 ÷ +10000 [digit] (degrees.tenths for temperature sensors).

Default:

0.5.

P168 - Reset Alarm 1 (Address ModBus 2168)
P182 - Reset Alarm 2 (Address ModBus 2182)
P196 - Reset Alarm 3 (Address ModBus 2196)
P210 - Reset Alarm 4 (Address ModBus 2210)

Alarm contact reset type

0

1

2
3

Automatic reset (

Default

)

Manual reset (manual reset form keyboard or digital input)
Manual reset stored (maintains the output status even after any power failure)
Automatic reset with time activation. The alarm remains active for the time set in the "Alarm delay" parameter P171, P185,
P199, P213, even if the conditions that generated it are no longer present. The alarm conditions must be cleared before
it can be triggered again.

«
...
43
44
45
46
47
...
»

Summary of Contents for REVO RT

























































Reviews:

No comments

Related manuals for REVO RT

Brand: Gardena Pages: 100

Brand: IBM Pages: 72

Brand: IBM Pages: 144

Brand: 7bit Pages: 2

Brand: Jafar Pages: 15

Brand: Baby Trend Pages: 8

Brand: Baby Trend Pages: 19

Brand: Baby Trend Pages: 5

Brand: Baby Trend Pages: 4

Brand: Bartec Pages: 26

Brand: Baninni Pages: 26

Brand: V2 Pages: 48

Brand: GAUGEMASTER Pages: 2

Brand: EasyIO Pages: 19

Brand: Zero 88 Pages: 2

Brand: Zenit Pages: 24

Brand: PAC Pages: 17

Brand: Datalogic Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands