Dial #
0000 + 078K # -
Code “K” gets assigned for accessing Second Junction Group.
Other Options
Every Junction can be given a separate access code = 1,2,3,4,5,7 or 8. It cannot be 9,0 or 6. If flexible numbering is done
then the first digit of the flexible numbers cannot be used.
Following programming can also be used to change the Junction access code from 9 to 0. But for that, first remove the
Operator code 9
. (Refer heading “
Operator Extension Setting”).
Programming procedure
Dial #
0000 + 0700 # - To make all Junction lines as normal. This is the default setting.
Dial #
0000 + 0720 # - To enable Manual LCR mode
Dial #
0000 + 0721 # - To disable Manual LCR mode
Dial #
0000 + 0730 # - PBX will allot a normal Junction line if the Special Junctions are busy.
Dial #
0000 + 0731 # - PBX will give engaged tone if the if the Special Junctions are busy.
Dial #
0000 + 0732 # - PBX will allot a Special Junction line if the Normal Junctions are busy.
Dial #
0000 + 0733 # - PBX will give engaged tone if the if the Normal Junctions are busy.
Dial #
0000 + 0740 # - To allow Incoming & Outgoing on Normal Junctions.
Dial #
0000 + 0741 # - To disallow outgoing on Normal Junctions.
Dial #
0000 + 0750 # - To allow Incoming & Outgoing on Special Junctions.
Dial #
0000 + 0751 # - To disallow outgoing on Special Junctions.
Dial #
0000 + 077 J # -
Junction “J” will be set as Special Junction. Where, J = 1 - 8 Junction number
Dial #
0000 + 0770 # - All Junction will be set as Special Junction.
Dial #
0000 + 076 J # -
Junction “J” will be in Normal mode. Where, J = 1 - 8 Junction number
Dial #
0000 + 0760 # - All Junction will be in Normal mode.
Dial #
0000 + 078K # -
Code “K” gets assigned for accessing Special Junctions in case of Manual LCR mode.
Here, K = 1,2,3,4,5,7 or 8. It cannot be 9, 0 or 6. If flexible numbering is done then the first digit of the
extension numbers cannot be used here.
To change the Junction access code from 0 to 9:
First remove the Operator Access Code 9
(Refer heading “
Operator Extension setting”). Then program as below:
Dial #
0000 + 0720 # + 0731# + 0733# + 0770# + 0789#
.
Junction Line - FLASH
.
To send FLASH on Junction line for using Call Waiting on the Telephone Line, do the following
:
FLASH while talking on the Junction Line
Dial # 8
.
Junction Line Ring Assignment
.
Junction lines incoming ring can be set in the following 2 modes
:
Auto Attendant Mode
(PBX gives Welcome message. Refer “Auto Attendant Mode Setting” for this.)
Direct Ring Mode
(Calls land on Operator or defined extensions in Simultaneous Ring mode or Round Robin
Ring mode)
Direct Ring Mode (Simultaneous / Round Robin)
To set Junctions in Direct Ring mode, following are the programs
:
Dial #
0000 + 11 # (To set all Junctions in Direct Ring mode)
Dial #
0000 + 11 J # (To set selected Junctions in Direct Ring mode)
Here, J= 1 to 4 (Junction in Direct Ring Mode)
Note
:
When a junction is set in “Direct Ring Mode”, “Auto Attendant Mode” automatically gets cancelled.
Now to define Junction landing in Simultaneous or Round Robin mode, do the following programming:
Simultaneous Ring
In this mode, incoming Junction lines ring on one or more Extensions.
Incoming ring of Junction Lines can be programmed separately for Day and Night modes as described below:
Dial #
0000 + 3X J # This program
disables the default ring assignment
.
If this is not done then default rings will also continue
in parallel.
Dial #
0000 + 3 X J NN 0 #
Here, X= 0 for Day Mode and 1 for Night mode.
J = 1 to 4 (Junction Line no)
NN = Last 2 digits of the Extension No. (It can only be from 01 to 16. Cannot program Extension 617 to
632 in case of 432S.
This programming can be repeated for one Junction Line and up to 16 Extensions.
One Junction line can be programmed to land on up to 16 Extensions.
Dial #
0000 + 3X J # (To disable Ring Assignment of one Junction)
Dial #
0000 + 3X J NN 1 # (To disable Ring Assignment of one Junction & Extension)
Default
:
All the Junction Lines land on Extension number 601 and 602 in Simultaneous Mode.
Example:
To assign Extension numbers 601, 602 & 605 to ring for incoming calls on Junction number 2, in
Day Mode
:
Dial #
0000 + 30 + 2 # + 30 2 01 0 # + 30 2 02 0 # + 30 2 05 0 #