Some or all extensions can be programmed to get Junction Line on lifting the Handset.
To dial internal numbers, dial
on lifting the Handset. You will get internal dial tone of the PBX.
To program an extension to get a free Junction line on lifting handset,
Dial #
0000 + 2 NN 0 #
Where, NN= last 2 digits of Extension numbers that is to be programmed for Direct Junction Access.
Dial #
0000 + 20 # -
To convert all Extensions in “Hot Line to Junction” mode
Dial #
0000 + 2 NN 1 # - To convert NN Extension in normal mode.
Dial #
0000 + 21 # - To convert all Extensions in normal mode.
Note
:
When all Extensions are converted to Hot Line then to get into the Programming mode, lift Handset
– dial
#
0000
+ whatever Programming to be done.
.
Hot Line to Extension
(In selected models only)
.
Some or all extensions can be programmed to get connected to Operator Extension, on lifting the Handset.
To dial internal numbers, dial
on lifting the Handset. You will get internal dial tone of the PBX.
To program an extension in this mode,
Dial #
0000 + 883 NN #
Where, NN= last 2 digits of Extension numbers that is to be programmed for this feature.
Dial #
0000 + 883 # -
To convert all Extensions in “Hot Line to Extension” mode
Dial #
0000 + 884 NN # - To convert NN Extension in normal mode.
Dial #
0000 + 884 # - To convert all Extensions in normal mode.
Note
:
When all Extensions are converted to Hot Line then to get into the Programming mode, lift Handset
– dial
#
0000
+ whatever Programming to be done.
.
Junction Access During Power Failure
.
When the system is switched OFF, the Junction lines get directly connected to following respective extensions.
Junction Number Extension Number to which it gets connected
01
601
02
602
03
603
04
604
.
Junction Access Codes / Change
.
Junction lines can be accessed in rotation by dialing 9.
To access a particular Junction line, dial #11, #12, #13, #14 (11 represents the first junction Line and 14 the last one).
The Junction access code 9 can be changed to 0. Refer the heading
“
Junction Grouping
”
for procedure.
.
Junction Access in Circular / Sequential Mode
.
In case of dialing out on the Junction Lines, PBX can be configured to work in either of the following 2 modes:
Mode Description
Circular When an extension dials 9, the PBX will allot Junction numbers 01.
Next time any Extension dial 9, Junction number 02 will be allotted. Then 03. Then 01.
Sequential When an extension dials 9, the PBX will allot Junction numbers 01.
Next time any Extension dial 9 and if Junction 01 is free then Junction 01 will be allotted. Junction
number 02 will be allotted only when Junction 01 is engaged.
Programming
:
To program in Circular mode, Dial #
0000 + 0620 #
To program in Sequential mode, Dial #
0000 + 0621 #
.
Junction Access Control
.
Every Extension can be programmed to access one or all of the 3 Junction Lines.
The access to each Extension can be different in Day mode and Night mode.
Procedure
:
Dial #
0000 + 70 J NN X # (For Day Mode access)
Dial #
0000 + 71 J NN X # (For Night Mode access)
Where, J = 1, 2 ,3 or 4 representing the 1
st
, 2
nd
, 3
rd
& 4
th
Junction Line.
NN = Last 2 Digits of Extension Number
X = 0 to allow Junction access
1 to Disallow Junction access.
Dial #
0000 + 70 J X # (To allow/disallow all extensions to access “J” Junction in Day Mode)
Dial #
0000 + 70 NN 2 # (To allow “NN” extension to access all Junctions in Day Mode)
Dial #
0000 + 70 NN 3 # (To disallow “NN” extension to access all Junctions in Day Mode)
Dial #
0000 + 71 J X # (To allow/disallow all extensions to access “J” Junction in Night Mode)
Dial #
0000 + 71 NN 2 # (To allow “NN” extension to access all Junctions in Night Mode)
Dial #
0000 + 71 NN 3 # (To disallow “NN” extension to access all Junctions in Night Mode)
