Appendix
E-63
English
15:
Auto Wah
This is a “wah” effect that can automatically shift the frequency in
accordance with the level of the input signal.
Parameter Value Ranges:
0 : Input Level (0 to 127)
Adjusts the input level. The input signal can become distorted
when the level of the sound being input, the number of chords, or
the Resonance value is large. Adjust this parameter to eliminate
such distortion.
1 : Resonance (0 to 127)
Adjusts the strength of resonance.
2 : Manual (0 to 127)
Adjusts the wah filter reference frequency.
3 : Depth (–64 to 0 to +63)
Adjusts the depth of the wah in accordance with the level of the
input signal.
Setting a positive value causes the wah filter to open in direct
proportion with the level of the input signal, producing a bright
sound. Setting a negative value causes the wah filter to close in
direct proportion with the level of the input signal, producing a
dark sound. Even when the wah filter is closed, high level input
will cause it to reopen.
16:
LFO Wah
This is a “wah” effect that can automatically affect the frequency
using an LFO.
Parameter Value Ranges:
0 : Input Level (0 to 127)
Adjusts the input level. The input signal can become distorted
when the level of the sound being input, the number of chords, or
the Resonance value is large. Adjust this parameter to eliminate
such distortion.
1 : Resonance (0 to 127)
Adjusts the strength of resonance.
2 : Manual (0 to 127)
Adjusts the wah filter reference frequency.
3 : LFO Rate (0 to 127)
Adjusts the LFO rate.
4 : LFO Depth (0 to 127)
Adjusts the LFO depth.
17:
Flanger
This is a flanger that uses a sine wave LFO.
Parameter Value Ranges:
0 : LFO Rate (0 to 127)
Adjusts the LFO rate.
1 : LFO Depth (0 to 127)
Adjusts the LFO depth.
2 : Feedback (–64 to 0 to +63)
Adjusts the strength of feedback
3 : Wet Level (0 to 127)
Adjusts the level of the effect sound.
Multi-effect Algorithms
A multi-effect is one connected to multiple single
effects (page E-61).
“M01: Multi01 (Enhancer - Chorus)”, for example, is a
multi-effect connected to two single effects: Enhancer
and Chorus. The parameters included in a multi-effect
algorithm are the same as the each of the connected
single-effect algorithms. However, the following two
parameters are specific to multi effects.
***
Skip (Off, On)
This parameter is included in M05, M06 (Phaser Skip),
M08 (Wah Skip), etc.
It makes it possible for one of the effects of a multi
effect (such a Wah in the case of Wah Skip) to be
bypassed. Turning this parameter on causes the
corresponding effect to be bypassed.
Note that depending on whether
***
Skip is On or Off,
there may be some difference in the level of notes that
pass through the multi effect. Whether or not the level
difference occurs depends on the settings of the other
parameters of the multi effect. Adjust the Level, Depth,
and other parameters for the skipped effect as
required.
Routing
This parameter is included in M11 and M12. It swaps
the routing of the effect.
The following shows only the parameters of multi-
effect algirithms (M01 through M26).
M01: Multi01 (Enhancer - Chorus)
0 : Enhancer Low Frequency
1 : Enhancer Low Gain
2 : Enhancer High Frequency
3 : Enhancer High Gain
4 : Chorus Rate
5 : Chorus Depth
6 : Chorus Feedback
7 : Chorus Wet Level
M02: Multi02 (Chorus - Tremolo)
0 : Chorus Rate
1 : Chorus Depth
2 : Chorus Feedback
3 : Chorus Wet Level
4 : Tremolo Rate
5 : Tremolo Depth
6 : Chorus Polarity
