background image

2

6033701-R9 EN

TRUCK REQUIREMENTS

GA0390.eps

A

GA0082.eps

Carriage

Clean carriage bars and inspect 

carriage bars.  Make sure the bars 

are parallel and that ends are flush.  

Repair any damaged notches.

WARNING:

 Rated capacity of the truck/

attachment combination is a responsibility 

of the original truck manufacturer and may 

be less than that shown on the attachment 

nameplate. Consult the truck nameplate.

Clamp

(or Close)

Sideshift 

Right

Hoist Up

Auxiliary Valve Functions 

 

Check for compliance with ISO standards:

Tilt Back

Hoist Down

Sideshift 

Left

Tilt 

Forward

Release

(or Open)

Truck Relief Setting 

(see attachment nameplate)

  Low Pressure 

High Pressure

155 bar 

190 bar - Recommended

189 bar 

250 bar - Maximum

NOTE:

 The attachment valve has separate pressure 

relief control, see Installation Step 11 for adjustment.

Truck Flow Volume 

Min.

 

Recommended

Max. 

12G thru 64G 

19 L/min.

28 L/min.

56 L/min.

70G, 77G

26 L/min.

45 L/min.

75 L/min.

  Cascade Non-Revolving Clamps are compatible with SAE 10W 

petroleum base hydraulic fluid meeting Mil. Spec. MIL-0-5606 

or MIL-0-2104B.  Use of synthetic or aqueous base hydraulic 

fluid is not recommended.  If fire resistant hydraulic fluid is 

required, special seals must be used.  Contact Cascade.

  Flow less than recommended will result in reduced system 

performance.

  Flow greater than maximum can result in excessive heating, 

reduced system performance and short hydraulic system life.

Carriage Mount Dimension (A) ISO

Minimum

Maximum

Class II

Class III

Class IV

380.0 mm

474.5 mm

595.5 mm

381.0 mm

476.0 mm

597.0 mm

Summary of Contents for 20G

























Reviews: