background image

This document is the property of Carrier Corporation and is delivered on the express condition that it is not to be disclosed,
reproduced in whole or in part, or used for manufacture by anyone other than Carrier Corporation without its written consent, and
that no right is granted to disclose or so use any information contained in said document.

Carrier reserves the right to change or modify the information or product described without prior notice and without incurring any
liability.

©  2006, Carrier Corporation

          11-808-363-01  03/06

Touch

 

Pilot

Installation and Operation Instructions

Part Number 33CNTPILOT

Introduction ................................................................. 1

About this Manual .................................................. 1

Safety Considerations .................................................. 1

General ......................................................................... 1

Installation ................................................................... 1

Location ................................................................... 1
Power Transformer Wiring ...................................... 1
Carrier Network Communication Bus Wiring ........... 1

Communication Bus Wire Specifications ....... 1
Connection to the Communication Bus .......... 1

Mounting ................................................................ 2

Surface Mount ................................................ 2
Decorative Bezel ............................................. 2
Chiller Display Mounting ............................... 2

Operation ...................................................................... 4

Power-Up Display .................................................... 4

Default Device Designation ............................ 4
Default Group Designation ............................. 4

Group Display Screen .............................................. 4

To Remove a Point from a Group Display ....... 5
To Add a Point to a Group Display ................ 5

Navigation and Operation Pushbuttons .................. 5

BACK ............................................................. 5
HOME ............................................................. 5
MAIN MENU ................................................. 5
PREVIOUS ...................................................... 5
NEXT .............................................................. 5
OK .................................................................. 5
NO .................................................................. 5
CANCEL ......................................................... 5
CLEAR DATA ................................................ 5
RESET DATA ................................................. 5
ADD ............................................................... 5
REMOVE ........................................................ 5
INC, DEC ........................................................ 5
SCROLL UP, DOWN ...................................... 5

PAGE UP, DOWN ........................................... 5
FORCE ............................................................ 5
AUTO ............................................................. 5
MODIFY ......................................................... 5
ALARM INDICATOR LIGHT ........................ 5
START/STOP BUTTON ................................. 6

Main Menu .............................................................. 6

LOGIN ............................................................. 6
LOGOUT ......................................................... 6
SETUP ............................................................ 6
ATTACH ........................................................ 6
TIME .............................................................. 6
ALARMS ....................................................... 7
RESET ............................................................. 7
SCHED ............................................................ 7
STATUS, SETPNT, SERVICE, MAINT OR
CONFIG .......................................................... 7

Setup Menu Screen ................................................. 7

Configuration Tables ................................................... 8

User Configuration (USERCONF) Table .................. 8

BACKLIGHT ALWAYS ON? ......................... 8
FULL ACCESS PASSWORD .......................... 8
LIMITED ACCESS PASSWORD ................... 8
ACTIVE LANGUAGE PASSWORD ............... 8
ACTIVE LANGUAGE ..................................... 8
TIME FORMAT ............................................. 8
DATE FORMAT ............................................ 8
UNITS BASE .................................................. 8
CONTRAST CONTROL ................................. 9
NETWORK MODE ......................................... 9
ALARM ACKNOWLEDGER ......................... 9
BROADCAST ACKNOWLEDGER ................ 9
EQUIPMENT CCN ADDRESS ....................... 10
BUS NUMBER ............................................... 10
ELEMENT NUMBER ..................................... 10
CONTROL VARIABLES ................................ 10
EQUIPMENT STATUS ................................. 10
EQUIPMENT START/STOP ......................... 10
ALARM STATUS ......................................... 10
ALARM RESET ............................................. 10

Summary of Contents for Touch Pilot 33CNTPILOT













Reviews: