background image

Air Purifier Sizes 1620, 1625, 2020, 2025, 2420: Installation Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

8

A12251

Fig. 14 – Quick Connect Kit Installation Illustration

For mounting to fan coil air handlers:

1. Route the power conduit from the purifier to a knockout on the fan

coil air handler that provides access to the incoming power wiring

compartment. Affix the end of the conduit to the fan coil air handler

using the included conduit fitting.

2. Remove the yellow and black primary wires from the fan coil air

handler  transformer  terminals  and  connect  the  quick  connect

“piggyback” terminals of the quick connect kit leads exiting the air

purifier  power  conduit  assembly  to  the  transformer  terminals.

Reconnect the yellow and black primary wires to their respective

transformer  terminals  on  the  “piggyback”  terminals.  Attach  the

ground ring terminal on the third wire to fan coil air handler chassis

ground (

Fig. 13

 and 

Fig. 14

).

Power  connections  are  to  be  made  inside  the  fan  coil  wiring

compartment per local electrical codes, and the two in-line fuses that are

provided  with  the  air  purifier must  be  installed  in  the  fan coil  wiring

compartment.

START-UP AND OPERATION

Final Assembly

1. Install  the  Filter  Enhancement  Module  (FEM)  into  the  cabinet,

insuring that FEM is held firmly in place by the retention springs

and  that  the  high  voltage  connector/handle  is  facing  outward

(

Fig. 15

).

A11495

Fig. 15 – Installing FEM

2. Slide  the  filter  into  the  cabinet  next  to  the  FEM  with  the  filter

pull-tab  facing  outward  and  paying  particular  attention  to  the

airflow direction arrows (

Fig. 16

).

A11496

Fig. 16 – Replace Filter

3. Insert the brand logo into the front of the door panel. To insure that

the logo is installed in the proper orientation, first attach the door to

the purifier and then snap the logo into place with the text in upright

position (

Fig. 17

).

4. Affix the “Captures & Kills” label to the front of the purifier door

as desired.

CAUTION

!

UNIT COMPONENT DAMAGE HAZARD

Failure  to  follow  this  caution  may  result  in  equipment  damage  or

improper operation.

For Furnace Purifiers:

Black Lead - Connect to Hot (L1) or EAC-1 when provided.
White Lead - Connect to Neutral (L2) or EAC-2 when provided.
Green/Ground Lead - Connect to Appliance Ground (Chassis).

For Fan Coil Purifiers:

Black Lead - Connect to L1
White Lead - Connect to L2
Green Lead - Connect to Appliance Ground (Chassis)

Summary of Contents for DGAPAXX 1620














Reviews: