background image

17

System Setup

• INSTALL: Use to set the current date. Use the keypad

buttons to scroll to the correct date.

• EQUIPMENT: Always set to CONV even if the unit is

a heat pump.

• AUX2 IN: Always set to W.

• FAN TYPE: Set for either single or 2 speed. The default

is 2 speed. (See Note 3 below.)

• AUX1 OUT: If remote Fault Detection and Diagnostic

(FDD) monitoring is required select SYS.

• OCC: occupancy, always set to INPUT

NOTES:

1. For 2 speed unit, under SYSTEM SETUP: EQUIPMENT=

CONV, AUX2 I = W, and FAN TYPE = 2 SPEED

2. More sophisticated controller setups, including for DCV or

power exhaust, are available by referring to Table 11 options

3. Note 3: Fan speed options are:

 a.

1 speed

 b.

2 speed

 c.

2 speed: 1 heat, 1 cool (for future use)

 d.

3 speed: 1 heat, 2 cool (for future use; do not use 3 speed

setting for LC units)

NA = Not applicable

 

Table 10 — Standard Jade W7220 Controller Configuration for 1 or 2 Speed Unit

CONTROLLER MENU

ITEM

FOR SINGLE SPEED UNIT

FOR 2 SPEED UNITS

NOTE

DEFAULT

SET TO:

DEFAULT

SET TO:

SETPOINTS

MAT SET

53°F

38° to 70°F

53°F

38° to 70°F

LOW T LOCK

32°F

-45° to 80°F

32°F

-45° to 80°F

DRYBLB SET

63°F

48° to 80°F

63°F

48° to 80°F

Only displayed if using single DB OA sensor

ENTH CURVE

ES3

ES1 to ES5

ES3

ES1 to ES5

Only displayed if using a single enthalpy OA 

sensor

MIN POS

4.4 Vdc

2 to 10 Vdc

Only displayed if set up for single speed unit

MIN POS H

NA

NA

4.4 Vdc

2 to 10 Vdc

Only displayed if set up for 2 speed unit

MIN POS L

NA

NA

6.0 Vdc

2 to 10 Vdc

Only displayed if set up for 2 speed unit

SYSTEM 

SETUP

INSTALL

1/1/2010

Current date

1/1/2010

Current date

EQUIPMENT

CONV

CONV

CONV

CONV

Always set to CONV, even on HP units

AUX2  I

W

W

W

W

Always  set  to  W

FAN TYPE

2 speed

1 speed

2 speed

2 speed

 See Note 3

AUX1 OUT

NONE

SYS

NONE

SYS

Set to SYS for remote FDD monitoring

OCC

INPUT

INPUT

INPUT

INPUT

Always set to INPUT

Summary of Contents for CRECOMZR067A01

























Reviews: