background image

2

sor when outdoor-air temperature is too cold. Demand control

ventilation is supported.

This EconoMi$er X system can be used with 1 or 2 speed

indoor fan motor units. (All other speed settings listed are for

future use.)

The EconoMi$er X system utilizes gear-drive technology

with a direct-mount spring return actuator that will close

upon loss of power. The EconoMi$er X system comes stan-

dard with fault detection and diagnostics (FDD), an outdoor

air temperature sensor, and mixed air temperature sensor (al-

so called supply air temperature sensor). Outdoor enthalpy,

indoor (return) dry bulb or enthalpy, and CO

2

 sensors are

available for field installation. 

Standard integrated barometric relief dampers provide nat-

ural building pressurization control. An optional power ex-

haust system is available for applications requiring even

greater exhaust capabilities. The power exhaust set point is

adjustable at the EconoMi$er X controller.

See Tables 1-3 for package usage. See Table 4 for package

contents. See Table 5 for sensor usage.

 

 

 

 

* Shipped in hardware kit for field installation.

HW = Honeywell

IMPORTANT: These economizers meet all the econo-

mizer requirements as specified in ASHRAE 90.1, IECC

and California’s Title 24. Economizer must be installed

square to avoid damper leakage or damper binding.

Squareness tolerance is ± 

1

/

32

 inch.

IMPORTANT: Read these instructions completely before

attempting to install the accessory economizer.

Table 1 — Carrier Usage Chart

CARRIER MODEL NUMBER ECONOMI$ER

®

 X PART NUMBER

Small Cabinet

48/50FC*04-07

48/50GC*04-06

50HCQ 04-06

50KCQ 04-06

50TCQ 04-07

48/50HC, LC 04-06

48/50KC 04-06

48/50TC 04-07

CRECOMZR067A01

Large Cabinet

48/50HC 07-12

48/50LC 07

48/50TC 08-14

50HCQ 07-09

50TCQ 08-12

CRECOMZR069A01

Extra Large Cabinet

48/50HC 14

48/50LC 08-12

48/50TC 16

50HCQ 12

50TCQ 14

CRECOMZR071A01

Table 2 — Bryant Usage Chart

BRYANT MODEL NUMBER ECONOMI$ER

®

 X PART NUMBER

Small Cabinet

548J/580J/558J 04-07

549J/547J/559J/582J 04-06

581J/551J 04-06

581K/551K 04-06

582K/559K 04-07

CRECOMZR067A01

Large Cabinet

548J 08-12

549J 07-09

580J/558J 08-14

581J/551J 07-12

CRECOMZR069A01

Extra Large Cabinet

548J 14

549J 12

580J/558J 16

581J/551J 14

CRECOMZR071A01

Table 3 — ICP Usage Chart

ICP MODEL NUMBER

ECONOMI$ER

®

 X PART NUMBER

Small Cabinet

RGH/RAH 036-060

RGS/RAS 036-072

RGV/RAV 036-072

RGW/RAW 036-060

RGX/RAX 036-060

RHX/RHH 036-060

RHS 036-072

CRECOMZR067A01

Large Cabinet

RAS/RGS 090-150

RGH/RAH 072-120

RHH 072-102

RHS 090-120

CRECOMZR069A01

Extra Large Cabinet

RAS/RGS 150

RGH/RAH 150

RHS 150

RHH 120

CRECOMZR071A01

Table 4 — Package Contents

ECONOMIZER PART 

NUMBER

QTY

CONTENTS

CRECOMZR067A01,

CRECOMZR069A01

1

EconoMi$er Damper Assembly with 

Actuator and HH79AH001 (HW: 

C7250) Outside Air Sensor

1

Jade HW63AW002 (HW: W7220) 

Controller with Attached Harness*

1

HH79AH001 (HW: C7250) Mixed Air 

Temp Sensor*

1

50HE403859 2-(green) wire harness 

for mixed air temperature sensor*

1

48TMHSRSE--A20 4-Wire Harness*

1

Hood Assembly with Top and 2 Sides

1

Hood Divider

1

Aluminum Filter

1

Hardware Bag*

CRECOMZR071A01

1

EconoMi$er Damper Assembly with 

Actuator and HH79AH001 (HW: 

C7250) Outside Air Sensor

1

Jade HW63AW002 (HW: W7220) 

Controller with Attached Harness*

1

HH79AH001 (HW: C7250) Mixed Air 

Temp Sensor*

1

50HE403859 2-(green) wire harness 

for mixed air temperature sensor*

1

48TMHSRSE--A20 4-Wire Harness*

1

Hood Assembly with Top and 2 Sides

1

Hood Divider

1

Hood Filter Divider

2

Aluminum Filters

1

Hardware Bag*

Summary of Contents for CRECOMZR067A01

























Reviews: