background image

13

Installing Optional HH57AC081 Single Outside
Air Enthalpy Sensor

When using the HH57AC081 (Honeywell C7400S) enthal-

py sensor (Fig. 30) for outside air changeover, the existing

HH79AH001 (Honeywell C7250) dry bulb sensor must be re-

moved. The enthalpy sensor will be mounted in the same loca-

tion as the dry bulb sensor; see Fig. 1. When the enthalpy sen-

sor’s OA temperature, enthalpy, and dew point are below the

respective setpoints, the outside air can be used for free-cool-

ing. When any of these is above the setpoint, free-cooling will

not be available. Figure 29 shows the enthalpy boundaries in

the W7220 Jade controller. There are 5 enthalpy boundaries

(setpoints ES1 through ES5), which are defined by dry bulb

temperature, enthalpy, and dew point. ES3 is the default set-

ting. Table 7 shows the High Limit Curves for each setting. Im-

portant: to use the HH57AC081 sensor for outside air sensor,

the dip switches on the sensor must be set to OFF-OFF-OFF.

See Table 8.

The 2 gray wires with a plug from the EconoMi$er X har-

ness in the return chamber plug directly into the HH57AC081

enthalpy sensor. See Fig. 23 and 28 for wiring.

Fig. 29 — Enthalpy Curve Boundaries

 

Fig. 30 — HH57AC081 Dimensional, Connection and 

Switching Information

  

           LEGEND

Default Setting = OFF-OFF-OFF

ECONOMIZING

AVAILABLE

NOT AVAILABLE

ENTHALPY

RA

 HUM (%RH)

RA

 TEMP

TEMPERATURE

ABSOLUTE HUMIDITY

ES5

ES4

ES3

ES2

ES1

HL

P1
(T,RH)

P2 (T,RH)

SINGLE ENTHALPY

DUAL ENTHALPY

HIGH LIMIT

Table 7 — Single Enthalpy and Dual Enthalpy High Limit Curves

ENTHALPY 

CURVE

TEMP. DRY 

BULB (F)

TEMP. 

DEWPOINT (F)

ENTHALPY 

(btu/lb/da)

POINT P1

POINT P2

TEMP. (F)

HUMIDITY 

(%RH)

TEMP. (F)

HUMIDITY 

(%RH)

ES1

80

60

28.0

80

36.8

66.3

80.1

ES2

75

57

26.0

75

39.6

63.3

80.0

ES3

70

54

24.0

70

42.3

59.7

81.4

ES4

65

51

22.0

65

44.8

55.7

84.2

ES5

60

48

20.0

60

46.9

51.3

88.5

HL

86

66

32.4

86

38.9

72.4

80.3

DA

RA

OA

12

3

S-Bus

Temp & Humidity

HH57AC081

4-1/4 (108)

2-3/4 (70)

2-1/64 (55)

S-Bus

NOTE: Dimensions are in. (mm).

Table 8 — HH57AC081 Sensor Dip Switch Settings

USE

DIP SWITCH POSITIONS FOR SWITCHES 1, 2, AND 3

1

2

3

DA

OFF

ON

OFF

RA

ON

OFF

OFF

OA

OFF

OFF

OFF

DA

— Discharge Air (not used on EconoMi$er X)

RA

— Return Air

OA

— Outside Air

Summary of Contents for CRECOMZR067A01

























Reviews: