background image

30

9 - MAJOR SYSTEM COMPONENTS AND OPERATION DATA

According to the Regulation No. 640/2009 and amendment 4/2014 implementing Directive 2009/125/EC with regard to ecodesign 

requirements for electric motors.

Product

30XAS

30XAS

Option

Standard

Option 119

Motor type

Asynchronous

Asynchronous

Number of poles

8

6

Nominal input frequency

Hz

50

50

Nominal voltage

V

400

400

Number of phases

3

3

Motor included in the application domain of the regulation 640/2009 and amendment 4/2014

No

No

Sales leaflet for exemption

Article 2.1

Article 2.1

Ambient air temperature for which the motor is specifically designed

°C

70

70

9.6 - Electronic expansion valve (EXV)

The EXV is equipped with a stepper motor (2785 to 3690 steps, depending on the model) that is controlled via the EXV board. The 

EXV is also equipped with a sightglass that permits verification of the mechanism movement and the presence of the liquid gasket.

9.7 - Moisture indicator

Located on the EXV, permits control of the unit charge and indicates moisture in the circuit. The presence of bubbles in the sight-glass 

indicates an insufficient charge or non-con-densables in the system. The presence of moisture changes the colour of the indicator 

paper in the sight-glass.

9.8 - Filter drier

The role of the filter drier is to keep the circuit clean and moisture-free. The moisture indicator shows, when it is necessary to change 

the element. A difference in tempera-ture between the filter inlet and outlet shows that the element is dirty.

9.9 - Sensors

The units use thermistors to measure the temperature, and pressure transducers to control and regulate system opera-tion (refer to 

the 30XA/30XAS/30XW Touch Pilot control manual for a more detailed explanation).

9.10 - 

Power factor correction capacitors (option 231)

They garantee a minimum power factor performance of 0.95 when unit operates at a condition that involves a power input that exceeds 

the Eurovent standard condition. 

A fix capacitor bank is switched at start of each compressor. It provides individual power factor correction for each machine refrigerant 

circuit.

Capacitors are dry type : no risque of leakage or fire.

The capacitors are selected for each compressor as per below table:

Compressor

Capacitor (kVAR)

06TTA266

35

06TTA301

35

06TTA356

35

06TUA483

45

06TUA554

45

CAUTION: Operation of the unit without capacitors results in current raising.

Summary of Contents for Aquaforce 30XAS Series









































Reviews: