Carrier 58SP0A Installation, Start-Up, Operating And Service And Maintenance Instructions Download

Page: 1 / 44

Installation, Start–Up, Operating and

Service and Maintenance Instructions

Read the entire instruction manual before starting the installation.
TABLE OF CONTENTS
SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Table 1 – Minimum Free Area Required for Each Combustion Air

opening of Duct to Outdoors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Table 2 – Minimum Space Volumes for 100% Combustion, Ventila

tion, and Dilution from Indoors . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Table 3 – Opening Dimensions - In. (mm) . . . . . . . . . . . . . . . . . 11

AIR DUCTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

GAS PIPING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Table 4 – Maximum Capacity of Pipe . . . . . . . . . . . . . . . . . . . . . 13

ELECTRICAL CONNECTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Table 5 – Electrical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

NOTES FOR THERMOSTAT WIRING DIAGRAMS. . . . . . . . . . 19

VENTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Table 6 – Minimum Allowable Input Rating of

Space-Heating Appliance in Thousands of BTUh per Hour . . . . 20

Table 7 – Combined Appliance Maximum Input Rating

in Thousands of BTUh per Hour . . . . . . . . . . . . . . . . . . . . . . . . . 21

Table 8 – Recommended Minimum Vent Height Per Furnace and Vent

Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

START-UP, ADJUSTMENT, AND SAFETY CHECK . . . . . . . . . 24

SERVICE LABEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Table 9 – Altitude Derate Multiplier for U.S.A. . . . . . . . . . . . . . 28

Table 10 – Orifice Size* and Manifold Pressure (In. W.C.) for Gas In

put Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Table 11 – Gas Rate (CU ft./hr). . . . . . . . . . . . . . . . . . . . . . . . . . 29

Table 12 – Blower Off Delay Setup Switch . . . . . . . . . . . . . . . . 30

Table 13 – Air Delivery - CFM (With Filter)* . . . . . . . . . . . . . . 31

SERVICE AND MAINTENANCE PROCEDURES. . . . . . . . . . . . 35

CARE AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Table 14 – Filter Size Information - In. (mm) . . . . . . . . . . . . . . . 37

SEQUENCE OF OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

PARTS REPLACEMENT INFORMATION GUIDE . . . . . . . . . . . 44

TRAINING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Most states in the USA and jurisdictions in Canada have laws that

require the use of Carbon Monoxide (CO) alarms with fuel burning

products. Examples of fuel burning products are furnaces, boilers, space

heaters, generators, water heaters, stoves/ranges, clothes dryers,

fireplaces, incinerators, automobiles, and other internal combustion

engines. Even if there are no laws in your jurisdiction requiring a CO

Alarm, it’s highly recommended that whenever any fuel burning product

is used in or around the home or business that the dwelling be equipped

with a CO Alarm(s). The Consumer Product Safety Commission

recommends the use of CO Alarm(s). The CO Alarm(s) must be

installed, operated, and maintained according to the CO Alarm

manufacturer’s instructions. For more information about Carbon

Monoxide, local laws, or to purchase a CO Alarm online, please visit the

following website. https://www.kidde.com.

Portions of the text and tables are reprinted from NFPA 54/ANSI Z223.1E, with permission of National Fire Protection Association, Quincy, MA

02269 and American Gas Association, Washington DC 20001. This reprinted material is not the complete and official position of the NFPA or ANSI

on the referenced subject, which is represented only by the standard in its entirety.

58SP0A/58SP1A

80% AFUE, Non-Communicating, Single Stage, ECM

Motor, Variable Speed, 4-Way Multipoise,

Non-Condensing Gas Furnace

WARNING

CARBON MONOXIDE POISONING HAZARD

Failure to follow this warning could result in personal injury and/or

death.

Carbon Monoxide (CO) is a colorless, odorless, and tasteless poisonous

gas that can be fatal when inhaled. Follow all installation, maintenance,

and service instructions. See additional information below regarding

the installation of a CO Alarm.

Use of the AHRI Certified TM Mark indicates a
manufacturer’s participation in the program. For
verification of certification for individual products,
go to www.ahridirectory.org.

D E

S I G N

E R

T I F I E

Summary of Contents for 58SP0A













































Search results

Summary of Contents for 58SP0A

Reviews:

Related manuals for 58SP0A

Brands by name

Popular brands

Carrier 58SP0A, Installation, Start-Up, Operating And Service And Maintenance Instructions

Search results

Summary of Contents for 58SP0A

Reviews:

Related manuals for 58SP0A

Brands by name

Popular brands