background image

58SP0A/58SP1A: Installation, Start–Up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

33

Unit Size: 070V21--20

Clg/CF Switch settings

External Static Pressure (ESP)

Clg Switches:

SW2-8

SW2-7

SW2-6

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1.0

Clg Default:

OFF

OFF

OFF

1930

1895

1855

1815

1775

1740

1700

1665

1630

1595

Cooling 

(SW2-8,7,6)

OFF

OFF

ON

810

735

660

585

505

See Note 4

OFF

ON

OFF

1010

945

885

820

760

695

625

565

510

455

OFF

ON

ON

1205

1150

1090

1040

985

930

875

820

760

705

ON

OFF

OFF

1400

1345

1295

1245

1200

1155

1105

1060

1005

960

ON

OFF

ON

1580

1540

1495

1445

1405

1360

1320

1275

1235

1190

ON

ON

OFF

1930

1895

1855

1815

1775

1740

1700

1665

1630

1595

ON

ON

ON

2245

2195

2145

2095

2045

1995

1935

1885

1835

1785

Maximum Clg Airflow

2

2245

2195

2145

2095

2045

1995

1935

1885

1835

1785

CF Switches

SW2-5

SW2-4

SW2-3

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1.0

Low-Clg Default:

OFF

OFF

OFF

810

735

660

585

505

See Note 4

Low-Cooling 

(SW2-5,4,3)

OFF

OFF

ON

585

490

See Note 4

OFF

ON

OFF

810

735

660

585

505

See Note 4

OFF

ON

ON

1010

945

885

820

760

695

625

565

510

455

ON

OFF

OFF

1205

1150

1090

1040

985

930

875

820

760

705

ON

OFF

ON

1400

1345

1295

1245

1200

1155

1105

1060

1005

960

ON

ON

OFF

1580

1540

1495

1445

1405

1360

1320

1275

1235

1190

ON

ON

ON

1930

1895

1855

1815

1775

1740

1700

1665

1630

1595

Cont. Fan Default:

OFF

OFF

OFF

810

735

660

585

505

See Note 4

Continuous Fan 

(SW2-5,4,3)

OFF

OFF

ON

585

490

See Note 4

OFF

ON

OFF

810

735

660

585

505

See Note 4

OFF

ON

ON

1010

945

885

820

760

695

625

565

510

455

ON

OFF

OFF

1205

1150

1090

1040

985

930

875

820

760

705

ON

OFF

ON

1400

1345

1295

1245

1200

1155

1105

1060

1005

960

ON

ON

OFF

1400

1345

1295

1245

1200

1155

1105

1060

1005

960

ON

ON

ON

1400

1345

1295

1245

1200

1155

1105

1060

1005

960

Heating (SW1)

Heat Airflow

3

1435

1385

1335

1290

1245

1195

1145

1100

1050

1000

Unit Size: 090V21--20

Clg/CF Switch settings

External Static Pressure (ESP)

Clg Switches:

SW2-8

SW2-7

SW2-6

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1.0

Clg Default:

OFF

OFF

OFF

1985

1935

1885

1835

1785

1735

1685

1630

1583

1532

Cooling 

(SW2-8,7,6)

OFF

OFF

ON

860

755

650

545

445

See Note 4

OFF

ON

OFF

1085

1000

910

830

735

655

565

485

405

310

OFF

ON

ON

1255

1180

1105

1025

950

870

790

715

640

570

ON

OFF

OFF

1425

1355

1290

1220

1150

1085

1015

940

870

800

ON

OFF

ON

1630

1575

1515

1455

1395

1330

1270

1210

1155

1090

ON

ON

OFF

1985

1935

1885

1835

1785

1735

1685

1630

1583

1532

ON

ON

ON

2100

2055

2010

1960

1915

1870

1820

1775

1715

1640

Maximum Clg Airflow

2

2100

2055

2010

1960

1915

1870

1820

1775

1715

1640

CF Switches

SW2-5

SW2-4

SW2-3

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1.0

Low-Cooling 

(SW2-5,4,3)

OFF

OFF

ON

700

575

See Note 4

OFF

ON

OFF

860

755

650

545

445

See Note 4

OFF

ON

ON

1085

1000

910

830

735

655

565

485

405

310

ON

OFF

OFF

1255

1180

1105

1025

950

870

790

715

640

570

ON

OFF

ON

1425

1355

1290

1220

1150

1085

1015

940

870

800

ON

ON

OFF

1630

1575

1515

1455

1395

1330

1270

1210

1155

1090

ON

ON

ON

1985

1935

1885

1835

1785

1735

1685

1630

1583

1532

Cont. Fan Default:

OFF

OFF

OFF

860

755

650

545

445

See Note 4

Continuous Fan 

(SW2-5,4,3)

OFF

OFF

ON

700

575

See Note 4

OFF

ON

OFF

860

755

650

545

445

See Note 4

OFF

ON

ON

1085

1000

910

830

735

655

565

485

405

310

ON

OFF

OFF

1255

1180

1105

1025

950

870

790

715

640

570

ON

OFF

ON

1425

1355

1290

1220

1150

1085

1015

940

870

800

ON

ON

OFF

1630

1575

1515

1455

1395

1330

1270

1210

1155

1090

ON

ON

ON

1630

1575

1515

1455

1395

1330

1270

1210

1155

1090

Heating (SW1)

Heat Airflow

3

1830

1775

1725

1675

1625

1570

1520

1465

1410

1360

Table 13 – Air Delivery - CFM (With Filter)* (Continued)

COOLING

4

 AND HEATING AIR DELIVERY - CFM (Bottom Return

5

 with Filter)

(SW1-5 and SW2-2 set to OFF, except as indicated. See Notes 1 and 2.)

Summary of Contents for 58SP0A













































Reviews: