Carrier 58SP0A Page 24 Installation, Start-Up, Operating And Service And Maintenance Instructions Download

Page: 24 / 44

58SP0A/58SP1A: Installation, Start–Up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

A03214

Fig. 38 – Horizontal Left Application - Vent Elbow Right then Up

A03218

Fig. 39 – Horizontal Right Application-Vent Elbow Right

A03215

Fig. 40 – Horizontal Left Application - Vent Elbow Up

A03216

Fig. 41 – Horizontal Left Application - Vent Elbow Right

A03219

Fig. 42 – Horizontal Right Application - Vent Elbow Left then Up

Venting Notes for

Fig. 31

Fig. 42

1. For common vent, vent connector sizing and vent material: United

States-use the NFGC.

2. Immediately increase to 5-in. (102 mm) or 6-in. (152 mm) vent

connector outside furnace casing when 5-in. (127 mm) vent

connector is required, refer to Note 1 above.

3. Side outlet vent for upflow and downflow installations must use

Type B vent immediately after exiting the furnace, except when

factory-approved Downflow Vent Guard Kit is used in the

downflow position. See Product Data Sheet for accessory listing.

4. Type-B vent where required, refer to Note 1 above.
5. A 4-in.(102 mm) single-wall (26 ga. min.) vent must be used inside

furnace casing and when the factory-approved Downflow Vent

Guard Kit is used external to the furnace. See Product Data Sheet

for accessory listing.

6. Accessory Downflow Vent Guard Kit required in downflow

installations with lower vent configuration. See Product Data Sheet

for accessory listing.

7. Chimney Adapter Kit may be required for exterior masonry

chimney applications. Refer to Chimney Adapter Kit for sizing and

complete application details. See Product Data Sheet for accessory

listing.

8. Secure vent connector to furnace elbow with (2) corrosion-resistant

sheet metal screws, spaced approximately 180° apart.

9. Secure all other single wall vent connector joints with (3) corrosion

resistant screws spaced approximately 120° apart. Secure Type-B

vent

connectors

per vent

connector

manufacturer’s

recommendations.

START-UP, ADJUSTMENT, AND SAFETY

CHECK

SEE NOTES: 1,2,4,5,7,8,9 on the page
following these figures

SEE NOTES: 1,2,4,7,8,9 on the page
following these figures

SEE NOTES: 1,2,4,5,7,8,9 on the page
following these figures

WARNING

FIRE HAZARD

Failure to follow this warning could result in personal injury, death or

property damage.

This furnace is equipped with manual reset limit switches in the gas

control area. The switches open and shut off power to the gas valve, if a

flame rollout or overheating condition occurs in the gas control area.

DO NOT bypass the switches. Correct problem before resetting the

switches.

SEE NOTES: 1,2,4,5,7,8,9 on the page
following these figures

Summary of Contents for 58SP0A













































Search results

Summary of Contents for 58SP0A

Reviews:

Related manuals for 58SP0A

Brands by name

Popular brands

Carrier 58SP0A, Installation, Start-Up, Operating And Service And Maintenance Instructions

Search results

Summary of Contents for 58SP0A

Reviews:

Related manuals for 58SP0A

Brands by name

Popular brands