background image

Packaged rooftop units

24

Pre-assembly roofcurbs

The 50EN/EH unit can be attached to a standardised pre-assembly 
roofcurb with adjustable height, built in galvanised steel panelling with 
polyester paint and thermal insulation.

Gas burner

-  Natural gas or propane gas burner with proportional actuator 0-10V 

designed in accordance with the standards in force in compliance 
with the Gas Directive 90/396 EEC (see EC homologation certi

fi

 cate 

of the unit with burner in speci

fi

 c gas burner brochure).

-  The electronic control of the 50EN/EH unit will only be managed 

by the burner connection as support for the heating depending on 
ambient conditions. The control will also receive from the burner a 
safety signal in the event of failure.

-  The burner module is 

fi

 tted with a controller installed inside as 

standard. This controller is used to manage, con

fi

 gure and diagnose 

all the operating parameters and safeties in the burner. 

The burner module includes a name plate featuring the main gas 
characteristics as well as the 50EN/EH unit serial number on which it 
is to be mounted. 

Important: All the necessary information about the installation, 
commissioning and maintenance of the burner module  is available 
in the specifi c instruction brochure on gas burner (supplied with 
the burner).

The serial number must be used in all communication 
regarding the unit.

m3/h 

mbar 

GAS INFORMATION

COUNTRY

GAS

CATEGORY

PIN

CONSUMPT.

PRESSURE

TYPE

WO

50EN/EH unit 
identifi cation No.

50EN/EH unit with burner 
CE certifi cate No.

Burner model

Important: All the necessary information about the installation of 
the roofcurb  is available in the specifi c instruction brochure on 
roofcurb (supplied with the roofcurb).

The following image shows a detail of the installation of the roofcurb on 
a roof. The levelling system uses angle pieces that allow adjustments 
in the X and Y axes.

The roofcurb is supplied thermally isolated, the installer must only do 
a sealing upsweep around the roofcurb to ensure that water does not 
penetrate the roof.

Summary of Contents for 50EH





































Reviews: