![background image](http://html.mh-extra.com/html/carrier/39t/39t_installation-start-up-and-service-instructions-manual_2562109044.webp)
Face and Bypass Damper Linkage —
All face and
bypass damper sections are shipped completely assembled
and operational. Sizes 07-11 are built as single assemblies.
Sizes 13-61 have two damper assemblies linked by a jack-
shaft. Sizes 74 and 92 have 3 damper assemblies linked by
two jackshafts.
All damper crankarms have 90 degrees of travel from open
to closed. They can be adjusted to suit the actuator location.
The face and bypass operating shaft is extended through
both sides of the unit. Actuators can be linkage connected or
direct connected. For direct conection actuators remove factory-
installed crankcarm. See Table 18 for operating torque
requirements.
Table 18 — Damper Operating Torque (lb-in.)
DAMPER
SECTION
39T UNIT SIZE
07
09
11
13
17
21
26
32
39
49
61
74
92
BOTH DAMPERS
INTERCONNECTED
MXB*
26
35
42
49
66
80
100
122
150
188
232
260
352
FMB*
EACH DAMPER
SEPARATE
MXB*
22
29
35
41
55
67
83
102
125
157
194
217
294
FMB*
EXHAUST AIR
EXB*
22
29
35
41
55
67
83
102
125
157
194
217
294
FACE & BYPASS
FBP
35
45
55
65
85
105
130
160
194
245
305
370
460
ZONE DAMPERS
(see Note 2)
ZDS
12
12
12
12
12
12
12
12
12
12
12
12
12
No. of Zones
5
5
6
7
7
7
8
9
9
11
12
14
14
*Observe the following cautions:
Do not exceed 3 in. wg negative pressure in these damper
sections.
Factory duct collars and damper assemblies are for attach-
ment of ductwork only and must not be used to support the
weight of the duct. Weight bearing deflection can increase
torque necessary to operate dampers, or bind them pre-
venting any movement.
NOTES:
1. Damper shaft moves 90 degrees from open to closed position.
2. Operating torque is shown for one zone. Multiply the value shown
by the number of zones for total with one actuator.
3. See Table 1 for section identification.
44
Summary of Contents for 39T
